Auto Parts and Repairs
Windshields and Wipers
Oldsmobile Cutlass
Chevy Blazer S-10

How do you replace a wiper motor for a 1999 Olds Cutlass?

123

Top Answer
User Avatar
Wiki User
Answered
2014-10-07 01:38:44
2014-10-07 01:38:44

Remove the wiper arm from your 1999 Oldsmobile Cutlass wiper motor. Remove the wiper motor wiring harness. Remove the wiper motor retaining bolts. Reverse the process to install the new wiper motor.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


how do you replace the wiper motor pulse board on a 1999 Chevy Silverado 2500

remove the cowl & wiper arms (mark location of arms on the windshield). disconnect the battery, Disconnect wire connector at wiper motor & remove the 4 mounting bolts then remove the linkage from motor.

the relay is built inside the motor. might need to replace the motor..could be costly.

? wiper switch toyota camry 1999 replace

Take off the cowling, and disconnect the wiper arms from the motor shaft. Then remove the 3 bolts holding the Motor, inside the engine compartment. Make note of arm placement, and cycle the motor before connecting the arm. Wrong placement could damage wiper arms, hood, glass ...you. You can watch the process on YouTube; the video will show you how to replace the wiper motor (see Related Links).

it is located on the front of the wiper motor.

to repair is just about useless, may as well replace it. to remove ..open plasticcap over the spindle nut and remove nut and washer, then open tailgate door and remove trim panel, disconnect wiring connector from wiper motor and remove mounting bolts, pull motor out and replace.

The windshield wiper motor is under the front cowl. After removing the cowl the motor should be easily accessed for replacement.

If your question is regarding the Ford Windstar, the answer is that the glass is exactly the same size / dimension. Yes, it will fit.

The oxygen sensor on the 1999 Oldsmobile Cutlass Sierra is located on the lower exhaust. If you need to replace it, they are available for about $20 online.

It depends on if it has air conditioning or not

# Disconnect negative battery cable # Mark the positions of the wiper arms on the windshield then remove the wiper arms # Remove the cowl grille # Working through the cowl opening remove the iper linkage mounting bolts # Remove the assembly turn it over and disconnect the wiper motor electrical connector # Pry off the drive link with a screwdriver hold the motor drive crank with a wrench remove the nut and detach the crank then remove the three screws and detach the motor

How to remove the window motor from the regulator

Look against the firewall at the center area

I believe its right under a cover on the wiper motor. Theres like 3 or 4 screws that hold the cover on and after you take the cover off the front of the wiper motor the module should be right there.

(1) Pull the rear wiper arm cover back to access the wiper arm retaining nut and detach the nut and pull the wiper arm straight off the shaft. (2) Open the rear hatch glass and remove the rear wiper motor cover. (3) Disconnect the electrical connector from the motor. (4) Remove the motor mounting screw and remove the motor. Installation is the reverse of removal.

take the complete headlight assembly loose or out to get to the bulb.

how to replace a blend door actuator on a 1999 ford ranger

i believe the 1999 - 2006 have a recall on the wiper motor. see your dealer.

The windshield wiper relay switch, on your 1999 Cadillac Deville, are located mounted to the firewall in the engine compartment. The relay switch will be next to the windshield wiper motor.

On a 1999 Olds Cutlass, the water pump is located in the engine compartment under the hood. It is on the motor on the passenger side of the vehicle.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.