0
How do you replace camshaft position sensor in 1998 Jeep Cherokee Sport?
Wiki User
∙ 13y ago
Assuming you are asking about a 4.0L engine... Remove the distributor cap. Remove the rotor. Unplug the camshaft positioning sensor from the harness. Lift carefully where the cable feeds through the distributor to the CMP and remove. Put replacement CMP in the same place and connect it to the harness. Replace the rotor and distributor cap. Courtesy of xjtalk.com
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Where is the camshaft position sensor located on a 1997 Jeep Grand Cherokee Limited 4.0?
On my 94, I6, it was lower right, from the front of the vehicle. There is a wire from the distributor to the sensor. Follow that.
Do the computer need reprogrammed after replacing the camshaft position sensor in 2000 Jeep Grand Cherokee 4.7?
Reprogrammed, no. The code cleared to turn off a check engine light, yes.
Is the camshaft position sensor repairable?
First unplug and plug back in before replacement. this most often works .
What is code P0720 on a 98 jeep grand Cherokee 4.0?
DTC P0340 - Camshaft Position Sensor Circuit MalfunctionSymptoms can include:Hard starting or no startRough running / misfiringLoss of engine powerCauses:A code P0340 could mean one or more of the following has happened:a wire or connector in the circuit could be grounded/shorted/brokenthe camshaft position sensor may have failedthe PCM may have failedthere exists an open circuitthe crankshaft position sensor may have failedPossible Solutions:With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:Visually inspect all the wiring and connectors in the circuitCheck for continuity in the circuit wiringCheck the operation (voltage) of the camshaft position sensorReplace the camshaft position sensor as requiredCheck the crankshaft position circuit as wellReplace circuit wiring and/or connectors as requiredDiagnose/replace the PCM as required
Where is the location of the Camshaft Sensor on a 1995 5.2 liter V8 in Jeep Grand Cherokee Orvis Edition?
On my 97 jeep grand Cherokee, with the 5.2 liter v8, its located in the distributor, under cap & rotor.
How do you replace replace the camshaft position sensor?
In order to replace the camshaft position sensor, you would need to disconnect the electrical plug holding it in. Using a socket, hold down the bolt and remove the camshaft position sensor.
How do you replace the camshaft position sensor on a 1997 Plymouth voyager 3 L?
how do you replace the camshaft position sensor on a 1997 plymouth voyager 3l
Where is the camshaft position sensor located on a 1999 Oldsmobile Intrigue and how do you replace it?
where is the camshaft position sensor located on a 1999 Oldsmobile intrigue
Where is the camshaft position sensor on a 1993 4.0 L Grand Cherokee LTD?
On the top of the bell housing. thats the crank position sensor the cam sensor in a 93 is fixed in the distributor to replace it you need a new distributor
How to replace camshaft position sensor for vw jetta 1999?
how to remplace position of oxigen sensor
How do you replace a camshaft position sensor on a 2000 Nissan Xterra?
How do u replace the camshaft sensor for a 2000 Nissan xterra 3.3L and where is its locatoin
If you replaced the camshaft position sensor should you replace the crankshaft position?
I changed only the camshaft position sensor on my 2000 Kia Sportage. So I don't think so.
Cps sensor 1989 Jeep Cherokee?
The camshaft position sensor is inside the distributor. The crankshaft position sensor is in the top of the bell housing on the driver side.
Where is the camshaft position sensor on a 2006 Kia Sorento?
do you need to take off the timing belt to replace a camshaft position sensor on a 2006 kia sorento
How do you replace the camshaft position sensor on Nissan Altima?
The camshaft position sensor is located near the thermostat housing. You should replace the crankshaft position sensor as well. This one is much harder to locate....it is on the backside of the engine that is between the firewall and the engine block. Both use the same sensor.
How do you replace the camshaft positioning sensor ml27 cdi?
the camshaft position sensor is on the left side of the engine , at back on the upper side . you have to demont the conector , than unscrew and replace it
How do i install a 1997 dodge caravan 3.0 camshaft position sensor?
If I'm not mistaken, I think the camshaft position sensor on these engines is built into the distributor. You'd have to replace the whole thing.
