0
First unplug and plug back in before replacement. this most often works .
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
Where is the camshaft position sensor located on a 1997 Jeep Grand Cherokee Limited 4.0?
On my 94, I6, it was lower right, from the front of the vehicle. There is a wire from the distributor to the sensor. Follow that.
What is code P0720 on a 98 jeep grand Cherokee 4.0?
DTC P0340 - Camshaft Position Sensor Circuit MalfunctionSymptoms can include:Hard starting or no startRough running / misfiringLoss of engine powerCauses:A code P0340 could mean one or more of the following has happened:a wire or connector in the circuit could be grounded/shorted/brokenthe camshaft position sensor may have failedthe PCM may have failedthere exists an open circuitthe crankshaft position sensor may have failedPossible Solutions:With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:Visually inspect all the wiring and connectors in the circuitCheck for continuity in the circuit wiringCheck the operation (voltage) of the camshaft position sensorReplace the camshaft position sensor as requiredCheck the crankshaft position circuit as wellReplace circuit wiring and/or connectors as requiredDiagnose/replace the PCM as required
Do the computer need reprogrammed after replacing the camshaft position sensor in 2000 Jeep Grand Cherokee 4.7?
Reprogrammed, no. The code cleared to turn off a check engine light, yes.
How do you replace camshaft position sensor in 1998 Jeep Cherokee Sport?
Assuming you are asking about a 4.0L engine... Remove the distributor cap. Remove the rotor. Unplug the camshaft positioning sensor from the harness. Lift carefully where the cable feeds through the distributor to the CMP and remove. Put replacement CMP in the same place and connect it to the harness. Replace the rotor and distributor cap. Courtesy of xjtalk.com
Can a camshaft position sensor be good and show fault code P0021 and P0011?
On my 1999, I'm pretty sure the cam and the crank sensor will generate the same fault code. For the price of the sensors, I'd just change both. Eliminate any doubt about which one is at fault.
Where is the camshaft position sensor on a 2005 Ford Expedition?
Where is the camshaft position sensor on a 2005 Expedition?
95 crown vic Where is the camshaft position sensor?
The 1995 for Crown Victoria camshaft position sensor can be found on the back of the cylinder head. The camshaft position sensor will be labeled as such.
Camshaft Position Sensor on a Nissan Xtrail?
location of the camshaft sensor
Where is the camshaft position sensor on a 2006 Chevy HHR?
Do you have a video of the hhr camshaft position sensor
Where is camshaft position sensor on 97 Saturn?
There isn't a camshaft position sensor. If you are asking because of an error code you received, it is caused by a signal that mimics the same signal as a camshaft position sensor.
Where is the camshaft position sensor on a 2.2 Sunfire?
The Pontiac 2.2 liter engine camshaft position sensor can be found on the back of each cylinder head. The camshaft position sensor should be labeled as such.
Where is the camshaft position sensor located on a 2002 Daewoo laganza?
The camshaft position sensor is located on the end of the camshaft housing, on a 2002 Daewoo. The sensor should be labeled as such.
Where is camshaft position sensor on 5.7 Vortec?
The Camshaft sensor is located in the distributor.
Is a camshaft position sensor the same as a camshaft actuator?
no
Where is the camshaft position sensor peugeot 307?
by the camshaft
What does code P0344 mean on a dodge 97 caravan 2.4?
P0344 Camshaft Position Sensor Circuit IntermittentP0344 Camshaft Position Sensor Circuit Intermittent
Where is the camshaft position sensor located on 1990 Lexus ls400?
Where is the camshaft position sensor located on 1990 Lexus ls400?
