0
How do you replace door hinge pin bushings on a 1999 GMC sierra?
Wiki User
∙ 13y ago
I have a 1999 gmc 1500 sierra,need to replace door pins and bushings.door sagging.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you change the door hinge pins in a 1999 GMC sierra?
My advice based on experience is to replace the entire hinge assembly.
How do you fix a door that won't close on a 1999 jimmy?
Try replacing the hinge pin bushings. Common problem on these trucks.
How do you adjust the doors on a 1999 GMC Sonoma or S10 truck?
I've worked for GM for over 10 years. Look at your door hinge pins and bushings first, they are probably wore out. To tell if the pins and bushings are worn out, open the door and lift up on it from the end opposite the hinges. If the door has any play at all the pins/bushings are worn. If you let them go too long the holes in the hinge wear the bushings sit can get wallered out.
How do you replace the starter on your 1999 GMC sierra?
You put it where it belongs
How do you replace the hinges on a 1999 S-10 4.3?
In most cases you can restore the hinges with replacing the pins and bushings. Pin and bushing kits areavailable from your local auto parts store. If you need to replace the complete hinge it would require an extensive amount of work. The original hinges are welded in place to the door and the body pillar.
Repairing Worn Door Hinges on 1999 Astro Van?
The repair is to replace the entire hinge assembly.
How do you replace front door pin on a 1999 cadillac deville?
Buy a new or find a used door hinge . Forget about replacing the pin
1999 suburban my driver door hinge pin bushings have different od between the the top and bottom hinge no part stores show this in there books?
There are two different sizes of bushings for each hinge. On the Top door hinge the bushing go on the body side. The smaller of the two goes on the top hinge with the shoulder of the bushing on the top side of the hinge. The Larger bushing goes on the bottom of the hinge with the shoulder of the bushing on the bottom of the hinge. On the lower hinge the bushing go on the door side of the the hinge. The larger of the bushings go on the upper side of the hinge and the smaller bushing goes on the lower side of the hinge. When you put the pins in, the pin will go from bottom to top on the upper hinge and from top to bottom on the lower hinge. The pins will need to be tapped into place with a hammer. Be careful to not break the shoulder of the bushing. There is a tool that makes reinstalling the door spring a snap. It will probably cost $40, but it will save your knuckles and a lot of time. There are a couple of companies that make repair kits for these. On is from Dorman and the other is from HELP! The kits come with a small bushing, a large bushing, a pin, and a pin retainer. The retainers will look different depending on the company. Some look just like a thin washer and other look like an E-clip. If you go to an automotive parts house and ask for bushing and pin kits for you specific outfit they should know what you are talking about.
How do you replace the upper control arm bushings on a 1999 Ford Expedition?
I have 2000 expedition and thought i could change then. After taking my wheel off i notice they could not be change. You need to replace the upper control arm.
Where are the oxygen sensors on a 1999 Oldsmobile Cutlass?
The oxygen sensor on the 1999 Oldsmobile Cutlass Sierra is located on the lower exhaust. If you need to replace it, they are available for about $20 online.
How do you replace a lower ball joint on a 1999 Pontiac Sunfire?
you have to hammer out the three rivets that hold it to the control arm. but do yorself a favor and replace th whole control arm because the bushings on the arm are well known for falling out.
When was Sierra Sciences created?
Sierra Sciences was created in 1999.
