0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you replace a side view mirror on a 2002 Toyota sequoia?
The nuts holding the mirror to car are accessed by opening door and removing and door panels and/or trim that obstructs the nuts fastening the mirror to car.
How do you replace the cable in the door handle of a 2002 sequoia?
get a BFH
How do you replace a Toyota sequoia door handle cable?
This is done by removing the trim on the inside of the door. Then it is neccessary to remove the No1 service hole cover. Then one removes the door lock protector, the door handle protector, and detatch the control cable from the outside door handle. You then remove the door lock wire harness loops, and remove the lock from the door. Detach the old cable and reattach the new. and reverse the steps you just followed to reassemble the door.
How do you replace panel lights on a Toyota sequoia?
How do I replace the dash panel lights on a 2001 toyota sequoia?
How do you replace door check strap on Volvo V70?
open the door, remove door trim and the torque screw holding the strap to body, and two nuts holding strap to door and remove door stop from inside door
How do i replace the motor for a power window for a 1991 Chevy G20 van?
It is in the door. I suggest you take it to a trim shop to have it replaced.
How do you replace front door speakers on 2001 Toyota Sequoia?
You have to remove the door panels. You can use 6.5" speakers with a little bit of adaptation. You can search for door panel removal. There are 4 screws, a couple of clips and clips around the edge of the door panel.
How do you replace the driver's mirror on 1996 Chrysler Cirrus?
AnswerFRONT DOOR TRIM PANEL REMOVALRoll door glass down.If equipped, remove window crank Window CrankDisengage clips holding speaker grille to trim panel Front Door Trim PanelRemove screws holding door trim panel to door from around speaker opening.Remove screw cap from bottom of arm rest pull cup.Remove screw holding arm rest pull cup to support bracket behind trim panel.Remove screw cap from behind inside door latch handle.Remove screw holding door latch handle to door panel.Disengage clips holding trim panel to perimeter of door.Lift trim panel upward to disengage upper retainer channel.Tilt top of trim panel away from door.Disengage clip holding latch linkage to back of release handle Linkage ClipSeparate door trim panel from vehicle.INSTALLATIONPosition door trim panel next to door.Engage clip holding latch linkage to back of release handle.Position door trim panel on vehicle.Engage trim panel to upper retainer channel.Engage clips holding trim panel to perimeter of door.Install screw holding door latch handle to door panel.Install screw cap from behind inside door handle.Install screw holding arm rest pull cup to support bracket behind trim panel.Install screw cap from bottom of arm rest pull cup.Install screws holding door trim panel to door from around speaker opening.Engage clips holding speaker grille to trim panel.Install window crank handle, if so equipped.
How do you remove door trim on Ford telstar?
take screws out and pull door trim off
How do you open the rear hatch of a 97 Ford Expedition from the inside when the handle does not work and the door is locked shut?
remove the inside trim or cut a hole to reach the mechanism and replace the inside trim.
How to replace the door lock sensor on a C Class Mercedes?
To replace the door lock sensor you have to replace the door lock unit. You have to remove the door inside trim panel. To remove this trim panel carefully prise the top of the inside door handle ( use a plastic priser, a metal screwdriver may csratch). Remove torque screw inside handle. Next there is a plastic sign on the door trim panel that says "SRS air bag" Using your plastic priser prise it from the bottom. It should open like a trap door, inside there is another torque screw remove it. Carefully prise the trim panel from the door it is held on with plastic push on holders and a waterproof sealant. You should now be able to see the door lock Remove the door lock screws and unclip wires. To extract the lock from the door you have to remove the two revits holding the window sliding bar Carefully sneek the lock down and out through the opening at the bottom of the door. Reverse the process for fitting.
How do you get the door trim off a 1997 Ford Festiva?
How do you get the door trim off a 1997 Ford Festiva?"
