0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
what size bolt is used on idler pulley on a 4.3 2003 astro van?
Take the belt off, take the bolt off of the idler pulley, take the pulley off, put a new one on replace the bolt, and put the belt back on
How do you change the serpentine belt on 2003 Toyota Highlander?
Locate the idler pulley and release the tension. Remove old belt and replace it with the new one (there should be a sticker on the underside of the hood or on the radiator housing showing the path for the belt) and re-tighten the idler pulley.
How you change idler pulley on 2003 Nissan sentra 1.8?
The idler pulley on a 2003 Nissan Sentra 1.8 is changed by removing the engine accessories, removing the drive belts, and loosening the retaining bolt. The pulley can then be removed from the vehicle and a new one bolted into place.
How do you change a idler pulley on a 2003 Malibu?
First you would need to take the serpentine belt off of the engine, and then remove the bolt in the center of the idler pulley. I have included an instructional vieo of how this is done.
How do you replace wiper blades on a 2003 Dodge Caravan?
How to replace Wiper Blades on 2003 Dodge grand caravan ?
Where is the belt tensioner on a 2003 Dodge Grand Caravan Sport How do you loosen it to change the serpentine belt?
what you need is a ratchet 15mm socket. Losen the idler then slide off the serpentine belt off. There should be a diagram for routing the belt if not draw a diagram before removing it. Replace the serpentine belt crank it 2 or 3 times but don't start the engine. The 4th time start the engine this time the as the engine is idling eyeball the belt agaisnt the tensioner idler and crank pulley make sure the serpentine is algined. That's It. Bill A Note: Make sure that you have identified the tensioner pulley as apposed to the idler pulley. With the 15mm socket on the tensioner pulley's bolt, rotate it clockwise and this will release the tension on the belt, or in the case of installing a new serpentine belt, allow you to get it where it belongs. This is the case on my 1997 Dodge Caravan, and probably other year makes. Best of luck- Bryan 1993 Dodge Grand Caravan: Rotating the tensioner pulley's bolt clockwise was the way to replace my belt. By the way, the tensioner pulley in my van was one of the smaller ones in the middle of the whole system, attached to a silver arm coming off the tensioner.
How do you loosen the tensioner pulley in a 1996 Tracker?
We recently replaced the serpentine belt on our 2003 Chevrolet Tracker. We were able to place a wrench (I believe it was 9/16") on the tensioner pulley and apply pressure so the pulley released tension on the belt. This however did no allow enough slack to install the new belt so we removed the idler pulley at the top center of the engine. With the idler pulley removed we were able to route the belt and with the tension released on the tensioner pulley, routed the belt under the idler pulley and reinstalled the idler pulley, then released the tensioner pulley and the belt was installed. Be sure to note the exact route of the old belt before removal so the new belt follows the same path. Hope this helps.
How do you loosen serpentine belt on 2003 Rav4?
The serpentine belt on a 2003 Toyota Rav4 can be loosened by turning the retaining bolt on the idler pulley. The belt can then be shifted inward to loosen.
How do you replace a serpentine belt in a 2003 Pontiac aztek?
First you need really small hands to get in between the fender well and the idler pulley. You need a 3/8 inch break over to get in and pull the idler over to relieve the belt tension. Then you can slip the belt off and put the new one on in reverse order.
How do you change the serpentine belt on a 2003 Chrysler Town and Country 3.8L?
what you need is a ratchet 15mm socket. Losen the idler then slide off the serpentine belt off. There should be a diagram for routing the belt if not draw a diagram before removing it. Replace the serpentine belt crank it 2 or 3 times but don't start the engine. The 4th time start the engine this time the as the engine is idling eyeball the belt agaisnt the tensioner idler and crank pulley make sure the serpentine is algined. That's It. Bill A Note: Make sure that you have identified the tensioner pulley as apposed to the idler pulley. With the 15mm socket on the tensioner pulley's bolt, rotate it clockwise and this will release the tension on the belt, or in the case of installing a new serpentine belt, allow you to get it where it belongs. This is the case on my 1997 Dodge Caravan, and probably other year makes. Best of luck- Bryan 1993 Dodge Grand Caravan: Rotating the tensioner pulley's bolt clockwise was the way to replace my belt. By the way, the tensioner pulley in my van was one of the smaller ones in the middle of the whole system, attached to a silver arm coming off the tensioner.
How do you replace the cabin air filter on a dodge Dakota 2003?
A 2003 Dodge Dakota does not have a cabin filter.
How do you change the idler pulley in a 2003 Sedona?
According to Troy Dean Potensky's Auto Parts in Issaquah, Washington, you may have to see a professional for that if you know what I am saying ;)
