0
How do you replace or check the slave and master cylinder in a Plymouth lazer?
Wiki User
∙ 15y ago
underneath the car next to the transmission you should find the slave cylinder you can check it by looking into the clutch reservoir, the master cylinder is a huge cup on the fire wall white cap
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What if your clutch on your 85 Toyota corolla goes to the floor and is hard to shift?
There are two normal causes. The clutch is worn out or there is a leak in the hydraulic clutch slave or master cylinder. To check the clutch, press the clutch slave cylinder down. If the clutch slave cylinder bellows compresses down to the slave cylinder, the clutch is worn out. Check the clutch master cylinder fluid level. if this is low, then the clutch cylinder need to be checked. To check for a hydraulic leak in the clutch slave cylinder, remove the cylinder's bellows and check for any fluid. If fluid is present, rebuild or replace the cylinder and bleed the system. To check the clutch master cylinder, check the back the of clutch master cylinder for leaks. If fluid is present, replace or rebuild clutch master cylinder and bleed the system. In my experience, hydraulic leaks occur at the clutch slave cylinder.
How do you check the brake fluid in a 94 Plymouth sundance?
Master cylinder reservoir at driver's side firewall should have markings indicating full and low
Where do you check the brake fluid on a 1950 Plymouth special deluxe?
The Master cylinder is under the drivers side floor mat. You need to remove the metal plate to get at it.
When you first push brake pedal down it goes straight to the floorI need to pump brakes several times to get it to resume normal pressure 2003 silverado?
First thing I would do is check the fluid level in the Master Cylinder, and bleed the brakes. Start at RR, then LR, RF, and end up at LF, making sure you keep the Master Cylinder full at all times. If that does not help, replace the Master Cylinder.First thing I would do is check the fluid level in the Master Cylinder, and bleed the brakes. Start at RR, then LR, RF, and end up at LF, making sure you keep the Master Cylinder full at all times. If that does not help, replace the Master Cylinder.
How do you tell if the clutch master cylinder is gone out on a 87 king-cab Nissan truck?
first check your clutch slave cylinder for leaks, if its leaking ,replace and bleed system,if its not leaking,bleed system ,dont forget to bleed clutch damperand if its still not right, then replace clutch master cylinder.
Why is your brake pedal tight?
check the master cylinder.
How do you locate the clutch master cylinder and check the fluid level of the 1995 ford escort?
how do you locate the clutch master cylinder and check the fluid level of the 1995 ford escort
Where do you check the clutch fluid and how do you know if your clutch went out on a 1993 Nissan truck?
look at your clutch master cylinder and check fluid, if low ,check your slave cylinder for leaks ,its bolted on your transmission with 2 bolts ,its at where the boot is ,if leaking ,then replace ,if not then u will need anew clutch.
After replacing the master cylinder and bleeding the brakes on 1991 s10 Blazer you still have problems what could it be?
Check all of the wheel cylinders for any leaks. Check all of the lines for any kinks, then check the master cylinder again for any air. Air in the system may have gotten into the master cylinder and the cylinder may need bleeding again.
Leak in the cab of your 1991 Ford Ranger coming from the clutch What should you doshould you replace the entire clutch or is it just the line?
Replace clutch master cylinder and bleed system,also check your slave cylinder for leaks.its bolted to your transmission,the clutch cable is connected to it.
Why did your brakes lock on 52 Chevy?
Either one or more wheel cylinders are corroded and locked up or the master cylinder is locked up. First thing to do is check the master cylinder. Then check each wheel cylinder. Replace or rebuild any that are corroded or locked up. Replace all the brake fluid in the system. On a vehicle this old, I am sure the brake fluid is contaminated. Also a leaking wheel cylinder will cause a brake to lock up. One other possibility is a collapsed brake hose. Inspect them carefully.
How to tell whether the clutch slave cylinder needs to be replace and how to do it?
If there is fluid leaking from it in the engine bay in front of your tranny, its bad, also check the master cylinder on the floor board conecting your clutch pedal they can both leak brake fluid. Both are very easy to replace.
