answersLogoWhite

0


Best Answer

The rear bumper cover is held onto the frame by 4 bolts. They have a 13 mm head, and are accessed from under the van. They thread directly into the back of the bumper cover, therefore no nuts to worry about. The rounded edges of the bumper cover slide over a pin, so when the 4 bolts are removed, the bumper cover can be pulled straight off.

User Avatar

Wiki User

βˆ™ 2012-02-16 19:19:41
This answer is:
User Avatar
Study guides

Add your answer:

Earn +20 pts
Q: How do you replace rear bumper cover on 1993' Ford Aerostar?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Can you replace a 1989 Ford Aerostar transmission with one from a 1993 AeroStar If so are there any differences or modifications you have to do in order to make it work?

yes you can all you need to do is change the tail shaft cover between the two transmissions


How do you replace the rear bumper on a 1993 Saturn?

Open the trunk. Remove all the pushpin retainers. Look under the rear fenders.. remove any screws and pushpin retainers. Remove the braces, if any. Look under the bumper cover itself and remove any pushpins. When all these fasteners are removed, the bumper cover should just slide off. If you want to replace the whole bumper (metal and styrofoam included), take it to a pro or grab a service manual.


How do you remove the rear bumper cover on a 1993 Ford Taurus wagon?

To remove the rear bumper cover on a 1993 Ford Taurus wagon, the lights need to be disconnected in the rear. Once all electrical connections are disconnected in the rear, remove the taillights and the fuel filler overflow hose. Remove any nuts and bolts holding the bumper cover on. Using needle nose pliers, pop the push pins around the bumper cover upwards. Slowly pull on the bumper to remove it.


Picture of thermostat on a ford aerostar van-1993?

where is location of thermostat in ford aerostar van, 1993


Freon pressure for 1993 Aerostar with R-134a?

The 1993 Aerostar does not use R-134a. It uses R-12.


Is an alternator from a 1993 Ford Aerostar capadable to a 1994 Ford Aerostar?

Yes they are compatible


How do you get the ignition switch cover off so i may remove top cover of column in a 1993 ford aerostar?

never mind found out on 1993 models you have to take the whole column out and sterring wheel off to get at it thanks anyways


What are the cylinder positions on a 3 L motor on a 1993 Ford Aerostar?

On a 1993 Ford Aerostar 3.0 ( and 4.0 ) 3 - 6 2 - 5 1 - 4 front of Ford Aerostar


What type of engine oil does a 1993 ford aerostar XL use?

A 1993 Ford Aerostar would have come from the factory with ( 5W-30 )


How do I install the front bumper to a 1993 Acura Integra I have the bumper what hardware do I need to connect to the frame?

Just the bumper cover, or the reinforcement bar also? The cover goes on with either pins that go in and expand, couple of screws. If the whole assembly, a couple of bolts on each frame rail. Depends on what you are working with.


Where is the distributor on a 1993 aerostar 3.0 V6?

On a 1993 Ford Aerostar , 3.0L V6 engine : The distributor is located on the TOP of the engine , near the REAR


What oil weight does a 1993 Ford Aerostar XL use?

A 1993 Ford Aerostar ( 3.0L and 4.0L V6 engines ) came from the factory with ( 5W-30 )

People also asked