It's located under the dash on a bracket near the brake pedal arm. Push the brake pedal down and hold it. Turn the switch to the left and remove it from the mounting. Unplug the electrical connector. Pull the new switch's plunger out all the way, then push the brake pedal down as far as it will go and hold it. Line up the index key (guide) on the switch with the slot that is at the top of the square hole in the bracket and install switch. Make sure it's fully installed, then turn switch to the right to lock it in. Carefully pull up on the brake pedal until it's fully up. The switch plunger should rachet back to it's correct position. Plug the wiring connector on to the switch and check the brake lights to make sure they are working.
The brake pedal switch is bad. How do I replace it?
how to replace the brake light switch at the pedal of a 2001 ford zx2
look on the brake pedal you will see a lil switch there that's the brake light switch
you can find the switch on the back of the brake pedal.
Under the brake pedal. Looking up at the pedal you will see the switch it is srewed to the dash and rests on the metal arm of the pedal when you press the brake pedal the switch close's and the brake lights come on. To replace the switch it is very straight forward just remove the srew from the dash separate the wire and replace..
replace brake light switch on brake pedal
Should be attached to the brake pedal.....
the brake light switch is located on the arm of the brake pedal, above the pad. you will see a plunger-type switch that extends and retracts with the compression of the brake pedal. to replace it, unbolt it from the bracket attached to the brake pedal, disconnect the electrical connector, replace new part (compare the adjustment of the new switch with the old & adjust if necessary), connect electrical plug, mount new switch to bracket & test.
It's just above the brake pedal, connected to the brake pedal arm. The switch comes out with two screws and the new one plugs in. But before you replace the switch, check the adjustment.
Should be on the upper end of brake pedal
Follow the below steps to replace the Brake Light Switch on Chevy Blazer:1) Open the Chevy Blazer's driverdoor, and move the driver's seat as far back as it will go. Lean under the dashboard with the flashlight, and shine the light on the brake pedal arm to locate the brake pedal switch.2) Unhook the brake pedal wiring pigtail from the Chevy's brake pedal switch by hand. Unbolt the old brake pedal switch from the mounting bracket using the box wrench set.3) Remove the old brake pedal switch by hand. Insert the replacement brake pedal switch into the brake pedal bracket. Bolt the switch in place with the box wrench set.4) Plug the brake wiring pigtail into the replacement brake pedal switch by hand. Readjust the driver's seat, and close the door. Hope this helps.
It is above the brake pedal not under it. Follow the brake pedal bracket all the way up and you will see the brake pedal switch.
you need to replace the brake light switch that is located above the brake pedal underneath the dasboard Here's a link to a video that 1aauto.com has that shows you how to replace the brake light switch.
Check at the upper end of brake pedal under dash
This is usually cause by a stuck brake light switch on the brake pedal. Replace it.
the switch is located at the top back of brake pedal!!
Time for a new car ! Not a Chrysler product !
The 1999 Chevrolet Malibu brake light switch can be found beneath the dashboard, next to the brake pedal. The brake light switch simply plugs in and out.
There is a switch behind the brake pedal. Fairly easy to replace, or a 10 minute job at a garage.
It is attached to the brake pedal about halfway up. Take the clip off the pedal and slide the old switch off. Slide the new switch on, replace the clip and you are ready to go.
When the brakelite switch fails it fails to on. Replace the brakelite switch. Located under the dash on the brake pedal arm. You will see a push switch that is released when the brake is pressed. Just replace that switch.
Check the brake light switch on the brake pedal. Might have to replace it.
replace brake light switch located on brake pedal under dash
Located at the upper end of the brake pedal under dash area
Brake light switch is located on the brake pedal arm. Unbolt & bolt in new one. Wiring will unplug & plug back in to new switch.