0
How do you replace the ignition module on a 2001 Ford Taurus and what is the estimated cost for the module?
Wiki User
∙ 15y ago
The ignition module sits at the driver end of engine near the transmission, It is obvious as six plug leads come out of it. Remove all leads and connectors and unscrew four bolts on the corners of the module. I believe they are 7mm bolts on most '95 -'03 Taurus and Sable. Now fit you new module ans re-connect wires. All can be done in less than30 minutes, don't waste money taking it to a dealership.
Wiki User
∙ 8y ago
Wiki User
∙ 15y agoThere is no ignition module on this vehicle. The powertrain computer controls ignition with input from the crankshaft position sensor. It turn power on and off to the coils.
Add your answer:
Earn +20 pts
How do you replace ignition module in a 98' Malibu?
Remove the ignition module retaining ring. Pull the ignition barrel out. Remove the wiring harness from the back of the ignition barrel. Reverse the process to install the new ignition module.
Where is the ignition control module on a 1995 Ford Taurus sho 3.2?
if there is a DIS module (side of the air intake, pass side) then there is no distributor DIS = distributorless ignition system
Where is the ignition module on a 1994 Mercedes Benz SL-500?
am told my ignition module on my SL 500 is faulty where can i replace this and what exactly does it do?
How do you change ignition control module 1995 Buick Riviera?
Disconnect the battery. Remove the ignition coils. Remove the ignition control module that was under the coils, and replace it.
How do you replace the Ignition Module in the Chevy Celebrity?
To replace the ignition module in your Celebrity: Unplug the wires, take note of where they go so you can put them back in the correct place. Remove the screws that hold the ignition module in place. If the old module was coated with dielectric grease on the mounting surface put fresh dielectric grease on the replacement ignition module. Put the new ignition module in place and attach with the screws. Plug the wires back in their respective places.
Where can you find a diagram of a 1996 Ford Taurus ignition module?
CAR GUYS.COM OR YOU CAN GO TO YOUR LOCAL LIBRARY
How do you replace the ignition module on a 88 Ford Mustang?
88ford tempo
How do you replace the ignition in a 2001 Pontiac Grand Am?
ignition what? coil, swicth,module, lock cylinder? gm Jim
Where is the ignition module on a 1993 Ford Taurus located?
On the bottom side of the engine( front of the car) just below the exhause manifold. It is easiest to remove the mounting plate from the body of the engine, as balancing the coils on the module as you remove and insert screws if a real pain in the but. If anyone has any suggestions on waterproofing this area, I would greatly appreciate it, as I have gone through three of these modules in three years due to water getting into it and shorting the module out. This last time it was a coolant leak around a seal on the top of the water pump, spraying right into the module that caused it. Argh!
How do you replace the ignition module on a 1993 Chevrolet Blazer?
Find your distributor cap and follow the center cable to a rectangular part. This is the ignition module. Remove it, get a new one and install it.
How do you replace the ignition switch on a 1998 Audi A6 Quattro?
2002 Audi quattro 1.8 ignition module location
Is there a distributor - ignition control module on 1996 or newer Taurus - Sables?
AnswerSince 1996, engine ignition control has been handled by the Powertrain Control Module (PCM).The PCM has direct control over the ignition coils / coilpack (or coil-on-plug on some engines) - so the need for a 'distributor' has gone away.Coilpacks cost about $75Sidebar: without a distributor, the engine timing is also totally handled by the PCM.See "Related Questions" below for information about Ignition Control Modules on 1986-1995 Taurus/Sables.On a 1996 Ford Taurus the ignition control module is part of the drivetrain control module. To change the ignition control module you have to change out the computer. It is located behind the motor on the passenger side of the engine compartment. Look for a screw holding in a wiring plug with a dozen or so wires. The drivetrain control module has a couple of nuts holding it in place and looks like a cdrom when removed. Good luck. John
