answersLogoWhite
Dodge Caravan
Dodge Grand Caravan
Bumpers

How do you replace the rear bumper cover on a 2003 Grand Caravan?

616263

Top Answer
User Avatar
Wiki User
2011-01-09 16:49:14
2011-01-09 16:49:14

- Remove 3 screws in each rear wheel well (6 total). To get to bottom screw, take off wheel or lift car and use stubby screwdriver.

- Remove 2 screws in the rear hatch, 1 on each side. Must have the trunk door open to get to them.

- Pull out 4 plastic pins from along the bottom side of the bumper.

You can remove the bumper cover without removing the wheels. We used an offset screw driver (shaped like letter "Z"). It can be bought at any hardware store.

12

Related Questions

User Avatar

To replace a Pontiac Grand Am bumper cover, start by taking out either the three bolts on the side of the fender or in front of the wheels. Remove the top pushpins to remove the cover. Push back the two pins for each headlight, and pull them up. Unplug the lights. Then, get the replacement bumper, and snap it into place like the previous one.

User Avatar

if the bumper protector is damaged yes, or else the cover will have no suppot

User Avatar

how to install 2000 jeep grand cherockee Laredo front bumper cover

User Avatar

I do not believe there is a metal bumper. There is a foam insert that goes inside the bumper cover.

User Avatar

I need to replace the bumper cover on a Honda accord 98 EX 4door. is there a site where the screws and pags are?

User Avatar

how much will it cost to replace rear bumper cover on 2003 93 saab

User Avatar

The average cost for the part to replace the rear bumper cover on an Oldsmobile Intrigue varies between $88.00 and $124.00, depending on the year. The labor cost to replace the rear bumper will vary between $75.00 and $150.00 depending on the repair shop.

User Avatar

The rear bumper cover is held onto the frame by 4 bolts. They have a 13 mm head, and are accessed from under the van. They thread directly into the back of the bumper cover, therefore no nuts to worry about. The rounded edges of the bumper cover slide over a pin, so when the 4 bolts are removed, the bumper cover can be pulled straight off.

User Avatar

you take it off and then you put the new one on!

User Avatar

If the question is refering to the wiring harness that comes with a Grand Caravan with the optional towing package. The harness comes in a plastic bag somewhere in the interior of the vehicle but is not installed. The harness is installed by removing the rear bumper cover and tail light assemblies unplugging the lights from their respective harnesses and installing the harness between the light and connector that was just unplugged. The harness is simply routed out below the light assemblies under the bumper cover and out near the hitch receiver. Replace light assemblies and bumper cover and the installation is complete. The hardest part is stuffing the new harness connectors back in the body panel with the included padding to reduce noise from the connectors bumping against the body panel. The whole process can be completed in about 45 minutes.

User Avatar

Hello, Do you want to replace entire rear bumper or bumper cover? Are you doing it yourself or having shop do it? You can buy a new bumper cover (primed, so you'd have it painted too) for about $200. You can surely pick one up by hunting junkyards or sites like upullourparts.com Mike

User Avatar

I would replace the bumper cover. They are very flexible and any attempt to repair will probably not last long. There are several places that sell aftermarket oem replacements for around $140

User Avatar

The cam sensor on a 2002 Grand Caravan is located on the top of the engine. It is at the top, just below the valve cover.

User Avatar

It's behind the rear bumper on the left side or drivers side. You have to pull the bumper cover off in order to get to it.

User Avatar

To replace the dome light on a Grand Am, unscrew the light cover. Pull it down gently. Disconnect the light. Connect the new light, replace the light cover, and replace the screws.

User Avatar

Go to the person you got it from and ask them

User Avatar

On top of the intake cover on the right side.

User Avatar

In short, yes. Long Answer: Yes they truly are the same.

User Avatar

the front bumper cover has to be removed. other than that its not that hard.

User Avatar

It's located at the top of the engine and mounted on black plastic intake manifold cover (on the drivers side). It takes a bout three minutes to replace.

User Avatar

I think you would have to go purchase a new rear bumper cover or pick one up at a salvage yard. If you were to pick one up at a salvage yard, they could show you how to disconnect your old bumper cover and put your new one on.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.