answersLogoWhite
Thermostats
Mazda 929

How do you replace the thermostat located on a 1992 Mazda 929?

495051

Top Answer
User Avatar
Wiki User
2015-07-15 20:03:46
2015-07-15 20:03:46

On most cars the thermostat is on the top hose, but not this one. Find the bottom large hose and trace it up, there you will find three bolts to remove the lower cup that holds the thermostat. Be carfull because the uperhose has water in it, and your working right below it.

1

Related Questions

User Avatar

Where is the thermostat located and how do you replace it on 1992 toyota camry 4 cylinder ingine

User Avatar

Follow the lower radiator hose from the radiator to the thermostat.

User Avatar

The thermostat, on your 1992 Mazda, can be found on the front bottom portion of the engine. You can follow the water hose from the bottom of the radiator to the thermostat.

User Avatar

where is the thermostat located in a 1992 cutless supreme automobile

User Avatar

In the upper radiator hose, next to the side of the block (look above the alternator).

User Avatar

Drain the water from the cooling system of your 1992 Saturn. Remove the water hose. Remove the thermostat housing retaining bolts. Take the thermostat out. Reverse the process to install the new thermostat.

User Avatar

1992 Lexus es300 wear the thermostat is located

User Avatar

To replace a thermostat on a 1992 Geo Storm first locate the its housing. Once found drain the coolant system and remove the housing from the engine. Replace the thermostat.

User Avatar

follow the upper radiator hose from the radiator to the engine this is where youwill find the thermostat housing. remove ther housing and you'll be looking at the thermostat. it is realy easy

User Avatar

It is located at the engine end of the upper radiator hose. Take the thermostat housing off. When replacing the thermostat make sure the spring goes toward the engine. It is not the upper radiator hose...it is the lower one..

User Avatar

the bottom radiator hose goes right to it

User Avatar

The thermostat in a 1992 Honda Accord is found in the thermostat housing. The thermostat housing can be found by following the lower radiator hose.

User Avatar

follow lower hose to rear of engine. rember to bleed. bleeder located on the upper radiator hose housing.

User Avatar

It's where the lower hose meets the engine!! follow the upper radiator hose to the engine, and it is under a dome where the two meet.

User Avatar

The thermostat is located under the thermostat housing which is connected to the engine side of the upper radiator hose, and bolts to the intake manifold with 2 bolts. To replace, drain and properly dispose of coolant, remove upper radiator hose, and remove thermostat housing. The thermostat sits in a recess between housing and manifold. Replace with correct thermostat with the correct side facing engine, new gasket and a little sealant.

User Avatar

take out the flywheel and replace it with four banana peels, if this doesn't work take out the transmission and replace the fuel filter with a carton of milk.

User Avatar

Follow the hose at the top of the radiator on the driver's side. This connects to the water neck (from which protrudes the cooling fan switch). This neck is held on by two nuts. The thermostat lies between the neck and that to which it is bolted.

User Avatar

1992 Lexus es300 wear the thermostat is located

User Avatar

The thermostat in a 1992 Honda accord lx is located in housing that can be found when you follow the upper radiator hose back and finding where it connects to the engine.

User Avatar

What is a timing cover seal on a 1992 mazda 929 and where is it located at?

User Avatar

Follow the top rad hose. It's inside the thermostat housing.

User Avatar

Remove the top radiator hose from the thermostat housing, its the round thing up front of the motor that the hose leads to it from the radiator. Then remove the bolts holding on to the top part of the housing, replace and reset all parts removed.

User Avatar

To change that thermostat you need to follow the top radiator hose to the motor from the radiator. It will lead to the thermostat housing on the block. The housing will be anchored with (2) bolts to the block (I think). Take the housing off and the thermostat is housed inside.you will have to replace it with a manufactured suggested thermo(probably 180* or 200 degree thermo).

User Avatar

How do i replace speed sensor on 1992 toyota previa and where is the sensor located


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.