Trunk seal on an SL MB model 107.
go buy a new trunk seal at your local MB dealer or parts house...also get a tube of 3M glue. Line the trunk with newspaper or a tarp, it's going to get messy. Pull out the old seal...clean off everything but the paint...make the surface nice and clean. Without the 3M, lay the new seal down...make sure your seal is aligned properly and fits correctly...once you have it lined up correctly...break out the 3M....you won''t need a lot...a little will work fine...make it even and consistent....about 8"-12" at a time and slowly glue the seal down....go around the entire seal 2 or 3 times and make sure you have it adhered all around, and immediately wipe up any glue runs before it sets....I replaced mine this way, and when I was sure the seal was properly glued into place, I closed the hood and left it down for a couple of hours. that's it.
Front brake pads on a 560sl.....Buy a set of brake pads....don't get metalic...it will squeal like a pig farm and wear out the rotors twice as fast....get 4 brake wear sensors, a small tube of brake lube, and a can of brake cleaner, you'll need a hammer, a pair of pliers, a 1/4" punch, and some emery cloth...a paint brush.
Pull off the tires....remove the holding pins (2) from the caliper, using the hammer and 1/4" punch.....manipulate the brake pad spring....you might have to remove one of the pad sensors to do this. Depending on the wear of the pads, you might have to push the pads towards the caliper's pistons....using a flat blade screwdriver and avoid scarring the rotors. Slide the old brake pads up and out of the caliper. You'll probably have to use a lever of some sorts to push the pistons back into the calipers to allow room for the thicker, new pads.
Use the brake cleaner and brush to clean all the inside surfaces, and the small brake parts you just removed....clean everything.....lightly buff the disks with the emery cloth...take the shine off the disks....use the same emery cloth to lightly scuff the new brake pads....don't let any oil on the pads....take the brake lube and lightly coat the brake pins and very lightly, the back of the brake pads....very lightly.
Now...put it all back together....and remember...brake in these new pads....it takes about 40-50 miles to seat them in properly....test the brakes by driving down the street, apply the brakes, and make sure the car stops straight...if it turns sharply in either direction, you might have to re-clean the rotors or check the pistons in the calipers to make sure they're not stuck....
DOME LIGHT sl500 they pry out, using a small flat blade screwdriver....the entire clear lens unit pops out, and you replace the bayonet bulb.....that's it.
95 SL TOP REPLACEMENT
Personally, I would go to an upholstery shop for this....even the pros have problems installing these things...they have to be lined up perfectly....you need experience here....the tops themselves are expensive...and you don't want to mess it up....you also have to deal with the inside liner, which you have to take off first, and put back on.....there's also a lot of mechanical stuff you need to remove from the front...this job usually takes a pro team....2 or 3 guys...4-6 hours from start to finish. Also, with winter coming up....if you're planning on putting the hard top on for the winter....wait until spring....it doesn't make a lot of sense to install a new convertible top, just to store it.
I hope these answers help....DM
Replace weather seal.
in the trunk on the right side under the cover
Very carefully!
An Elephant Seal. It's kinda like a trunk.
This is an easy one.. Scince the trunk seal is a cut to length type of appplication you want the seam where the seal joins together to be at the back of the trunk near the latch. The trunk seal is glues to the underside of the trunk lid with weather strip adhesive. I like to put masking tap on both sides of the area where the seal gets glues to so I dont have glue all over the place. Then I smerar the glue in the area on the trunk that will hold the seal and then begin placing the trunk seal; starting at the latch area and working my way all around. source : AverageJoeResto.com and AAPD.net
Most likely it is coming in throgh the trunk seal. On a dry day wash your car and then open the trunk and see if the trunk seal is wet and there is a trail of water entering the trunk
Bad seal around trunk
Perhaps a bad door seal? Hole in floor? Rear windshield seal? Trunk seal? (check trunk area for water under spare tire etc.) Perhaps a bad door seal? Hole in floor? Rear windshield seal? Trunk seal? (check trunk area for water under spare tire etc.)
how do i replace a trunk lock with another lock that has a key
A bad trunk seal weatherstrip.
My 72 Impala's trunk will fill with water because the rear window seal leaks My 72 Impala's trunk will fill with water because the rear window seal leaks
The elephant seal and aardvark.