answersLogoWhite

0


Best Answer
Copy

you remove the 4 8mm bolts from pulley then loosen belt (iy will keep pulley from spining then its 3/8bolts along top and one hiden under center of water pump at the bottom 1/2 bolts in middle of and on both ends Power Steering pulley is in the and you must use a open end wrenchyou have to losen power steering pump or work it out if possible ( i don t know if you canthats where im at now i can t do the aggravating with it thing so i m gonna loosen and slide over it only needs to move an inch or so toward the firewall but its got to go i m trying to leave the ALL AMERICAN TOOL in its box will complete details when car is done 9/1/08

User Avatar

Wiki User

โˆ™ 2008-09-02 02:08:33
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you replace the water pump on a 1998 Buick LeSabre?
Write your answer...
Submit

Related Questions

Where is the solenoid on 1998 Buick lesabre?

The 1998 Buick LeSabre solenoid can be found on the firewall in the engine compartment. There will be three solenoids on the firewall.


How do you install a heater core on a 1989 Buick lesabre?

How do you install a heater core on a 1998 buick lesabre


Do you know why there is no heat coming from the heater on a 1998 buick lesabre?

no


How much does your 1998 Buick LeSabre weigh?

The 1998 Buick LeSabre custom sedan has a curb weight of 3,443 pounds. It has a wheel base of 110.8 inches and a ground clearance of 5.5 inches.


How do you read the firing order for a Buick Lesabre 1998 165432?

165432


What type of oil do you use on a 1998 buick lesabre?

10 30


Is 1998 Buick Lesabre a front wheel drive car?

yes


What type of antifreeze does a 1998 Buick leSabre take?

Dex cool


How do you replace a starter on a 1998 Buick Regal?

were can i locate and replace a starter for a 1998 buick regal?


Change struts in 1998 buick lesabre?

Struts on a 1998 Buick LeSabre are changed by jacking the vehicle up, removing the wheel, and unbolting the strut. It can then be pulled from its mounts and a new strut put in place.


Where is fuel shut off reset button on 1998 Buick LeSabre?

The fuel shut off reset button is located inside the 1998 Buick LeSabre. It can be found on the firewall in the front passenger side.


How many quarts of oil does a 1998 buick lesabre hold?

4.5 leaders


What size speakers are in the back of a 1998 buick lesabre?

6" x 9"


Where is the air filter on a 1998 Buick Lesabre?

under hood left side


What is the normal range on the temp gauge for a 1998 Buick LeSabre?

220-230


Is there a certain order to tighten the bolts when replacing the transmission in a 1998 buick lesabre?

No


Where is the fuel filter located on a 1998 Buick LeSabre?

On my 98 buick LeSabre the fuel filter was under the car passenger side just in front of the rear tire.Good luck!


How do you replAce license plate bulbs on 1998 buick lesabre?

If you can not remove fasteners on outside, you may need to cut a section out of the inside of trunk to get your hand by the bulbs.


1998 buick lesabre license plate bulb replacement?

The license plate bulb on a 1998 Buick LeSabre is replaced by removing the retaining screws and disconnecting the wiring harness. The bulb can then be twisted from the socket and a new bulb installed.


How do you replace the tether gas cap on a 1998 Buick Century?

how to replace the tether gas cap on a 1998 Buick Century?


What is the recommended tire pressure for 1998 buick lesabre?

32-35 psi


How to disconnect brake warning light and sound 1998 buick lesabre?

Cut the wire


Replace multi-function turn signal lever on 1998 Buick LeSabre?

lever pulled out, having trouble getting the lever locked back in place


How do you replace the alternator on a 1998 Buick LeSabre?

Disconnect the 98 LeSabre battery. Remove the alternator belt. Remove the alternator wiring. unbolt the alternator, remove it, and bolt the new one on. Reconnect the wiring, but the belt on, then reconnect the battery.


How do you reprogram a remote control for a 1998 buick lesabre?

In the owners manual it tells. On my 93 lesabre I had to jump two of the connetors on the code reader