free easy video instructions on www.vehix411.com
Set the odometer to TRIP A. Turn the key off. Press and hold the ODO button. Turn the key on. Continue holding the button while the light goes through a series of flashes. When it stops flashing, turn the key off and release the button.
Turn the key back on to make sure it "took".
maintenance with engine
disconnect the battery
How do you reset the maintenance required light in the 2011Toyota RAV4 with a smart key starting system
How to Reset Maintenance Warning Light on a 2008 Toyota 4Runner
Your drivers manual should give you the information to reset the oil maintenance light.
You will need to take it into a mechanic. They will be able to check out your vehicle and then they can turn off the light.
A maintenance light on a Toyota Camry can be reset by your mechanic after you have the work done that is needed. You also may be able to get instructions by checking your manual.
How do you reset maint read light on 2010 corolla
Resetting the maintenance light on a 1999 Toyota Tacoma is very easy to do. To reset the light, take the battery cables off for up to one minute to reset the light.
Check engine light or required maintenance light. Procedure for resetting required maintenance light just answered. Check engine light requires an OBD II to determine problem and turn the light off.
How do you reset maintenance reminder light on 2008 Toyota corolla? For what it is worth: To reset the Maintenance Required light on my 2007 Toyota Corolla: 1) Set your trip meter to the odometer setting (in other words, not Trip A or Trip B) 2) Hold down trip meter reset button and turn ignition to off. 3) While holding down the trip meter reset button now turn the ignition to on. 4) Keep holding down button until Maintenance Required light shuts off. Note: One some other Toyota models you hold down the Trip A meter rather than the odometer. Hope this works for you.
A person can reset the maintenance required light on a 2004 Toyota Sienna by holding down the odometer trip button. A series of zeroes will appear, which indicates that the light has been reset.
same as a 2005 odometer OS on turn key off hold reset turn key on loght flashes then turn off
The maintenance light,You will need to take it to a Dodge dealer to reset it. Or get a DBR-2 code scanner.BIG $$$
aperantly take the light out
Are you implying they are all the same? BClear.
The maintenance required light requires a scan tool to be reset.
To reset the maintenance required warning light on a 1989 Dodge Dakota, unhook the battery connector cables for 10 minutes. Reconnect them and start the vehicle.
With the engine and ignition off push and hold in the odometer reset button. While holding that button in, turn on the ignition but do not start the engine. After about 5 seconds the light will go off and the maintenance required light will have been reset.
How do you reset the maintenance light on a 2001 Honda accord ex I found some options at http://www.tegger.com/hondafaq/maintenance-reqd-light.html#why
Turn key off. Push mileage reset button. Keep it pushed in while you turn ignition key to on position. Hold for 10 secs...
Set the odometer reading to total miles and not to trip miles. Now press and hold the odometer reset button in and turn the ignition switch to the on position. (Do not start the engine). After around 5 seconds of holding the reset button in the maintenance required light will go off and be reset. Release the button and turn the ignition off.
Read your owner's manual.
You need a special computer for that. Check the gas cap first, make sure its tight, sometimes that sets it off.
To reset a 2007 Toyota Rav4, the steps are as follow:= = 1. Move odometer to Trip A then hold down. 2. Turn off ignition then turn on to ACC. (Don't turn on engine). 3. The reset will go through 000000.00 then _ _ _ _ _ going to ---- going to --- etc. 4. Once it runs through the reset, the maintenance required light flashes and goes off. 5. Easy fix, not sure why Toyota doesn't have this in the manual.