Insert the ignition key, and turn it to the ACC (accessory) position. Turn off the radio. Press the display button until Oil Life shows on the radio display. Press the seek button until Tire Pressure Monitor displays. Press the 2nd preset/#2 button. Press the display button again. The tire pressure monitor should now be reset.
In a 2000 to reset the low tire pressure light, first make sure the tires are properly inflated and then to reset the light pull the head light switch from off to parking lights and back to off 3 times. Otherwise it will say it your owners manual.
The light is on because there is a problem with the system. The light will remain on until the problem is fixed. Once the problem is fixed the light will reset itself after a short drive.
Check and adjust air pressure to specs in all the tires and it will set itself after a few miles of driving.
unhook a battery cable for about 3 minutes and re-hook.
Take it to a mechanic, and have them erase the codes. Auto zone and advance will not do it as they are not mechanics
AFTER you inflate the tires to the correct pressure, turn the ignition to the on position. Then pull the headlight knob from the OFF position to the parking light position three times. This should reset the system. This is the easiest way but you can also reset it through the radio. If you would rather do it this way, it is on 6-44 in your owner's manual
you eat 25 corndogs ! :]
Unhook the car battery.
General Motors cars do not have a reset switch.
how do I set reset ignition security on a 1999 z34 monte carlo
You have to have a computer programmer module, from O'Reily's or Autozone to reset it. Some will let you do it and some say that they are not authorized to do it. Good luck...
turn the ignition key to the on position (don't start) and depress the accelerator pedal 3 times within 5 seconds to reset the light.
No such thing on this car.
If you turn your radio off, and have the key on access. you should be able to push the volume button and bring up a menu on the factory radio. Check you owner's manuel. Same as with the oil change light.
You will most likely have to reset the light using the stock radio, the owners manual should tell you how to do it. You turn ur key to accessory, turn the radio off, then push and hold the display button. after this scoll to the tire pressure option using the seek button and enter this option by pressing the prev next buttons on the 1 and 2 of the radio.
turn the key to on. then press gas pedal to floor 3 times with in 5 second to do all three time. turn key off. if it does not work . repeat. that is for your oil reset. for your tires turn parking lights on and off 3 time in a row. that will reset tire light
Sometimes you can reset the security light on a Monte Carlo. Open all the doors and then lock them and close them. Next, use the key to unlock the front driver's side door. If this doesn't work, the car should be taken to a mechanic who can diagnose the problem. When the security light goes on, it can mean something in the security system is failing.
How to reset the tire pressure light on a 2007 Nissan Sentra?
When the tires are rotated, the system needs relearn tire position. This may also be a problem in the system if the warning on the dash says "service tire monitor system". There is a service bulletin to replace a few parts and re-program the system to correct this. - TechJK ------------------------------------ On what Car or truck. I need Year, Make, and Model to answer this! >A friend has a 2002 Monte Carlo where his "low tire pressure" warning has >been showing on his dash display. It only happens each time he has the >tires rotated. First time he had the GM dealer reset the light. All tires >are at the same and correct pressure...any ideas? Yes, this happened to me once. Simply reset the dashboard display after rotating tires. The system works on an imbalanced number of revolutions at the wheel sensor of the ABS. First, make sure that the four tires are identical and have identical pressure. Then reset the display.
hi how do i reset tire pressure sensor light on
Try turning ignition key to the on position (don't start) and depress the gas pedal 3 times within 5 seconds.
It does not have a reset. If the oil light is on, the sensor has failed or the oil pressure is too low.It does not have a reset. If the oil light is on, the sensor has failed or the oil pressure is too low.
Turn car on but don't start the engin. Pump breaks a couple times. Turn Key to off then start engin all the way. Light should be off.
take it too the deleship and have them reset the computer or some times you can disconnect the negative batery termanal and hook it back up and it will reset it
GM vehicles do not use inertia/reset switches.