answersLogoWhite

0


Best Answer

Depends if it is a cap or a plug or no hub or a brass /lead plug

User Avatar

Wiki User

12y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you take a cap off of a sewer clean out?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you get rust off a sewer pipe plug?

Wire brush BUT according to most model codes the sewer cap /plug should have been non ferrous metal


How do you clean camelbak?

It's pretty easy to clean a CamelBak. It's mostly like cleaning any other bottle, but I wouldn't put it in the dishwasher. You have to scrub it by hand. Take off the belley, (or the part that you drink) off and simply clean it. The top's harder, since there's three parts: the sucker, the straw, and the cap. Tug the straw that's connected to the sucker and cap off and clean it, then put it back on. (if you don't know how to do this, watch a youtube video), then take your sucker cap off and clean that to. (Watch youtube videos to understand this). What's leftover is the cap, and after taking off straw & sucker, clean the cap. Hope this helps. Some great youtube videos to help you clean a camelbak bottle are:Gear Review: Camelbak bottle (.75 mL)Camelbak ReviewWater bottle: Camelbak Better Bottle& many more! Hope y'all like it! :)


How do you check dthe power steering fluid on a 1998 jaguar xj8?

On most cars you simply take off the cap on the reservoir of the power steering fluid and the dip stick is attached to the cap. You clean it off, put it back on and pull it off again.


How do you install a rotor cap in a Chevy Silverado?

all you should have to do is take the distributor cap off, and there it is. answer take the distributor cap off, pull the old rotor off, put the new one on, put the cap back on.


When the engine has cooled off will you still have pressure from the radiator cap when you try to take the cap off?

no


What tool do you need to remove a cemented on cap off of a drain pipe?

Cut the end of the cap off, about 1/2 inch back from the end and then cut the side of the cap. You should be able to peel the cap off of the pipe. If you have enough pipe, just cut the entire cap off and start with a clean section.


Do you take off the cap of a lava lamp?

No you do not.


How do you do level 30 in factory balls 3?

1.Put in red 2.Put on cap 3.Put in chemical 4.Take cap off 5.Rotate five times 6.Put on cap 7.Put in chemical 8.Take off cap 9.Rotate once 10.Put on cap again 11.Put in chemical 12.Take off cap 13.Rotate twice 14.Put on cap 15.Put in red 16.Put in chemical 17.Take off cap AND YOUR DONE


The toilet and bath are cloged- took the cap off the tube outside and toiledt water gushed out. how do i fix this?

If you are on city sewer, the line to the sewer is either clogged or collapsed. You will need to have a plumber check it out. If you are on a septic tank, it may be full and need to be pumped out.


How do you take off a stubborn sewer cap?

you could try some how getting it covered in boiling hot water, or use a wrench, in desprate times I'd call for proffetional help. Many times you need a chisel and hammer and just replace the plug


How do you take a single handled faucet off a bathtub?

You have to pop the cap off on the front of the acrylic handle, then under the cap there will be a screw to undo.


How do you clean gunpowder off cap gun?

while you use the gun,after using it open,the cap gun put water on it. if it did,nt go you can use cloths