Chevy Tahoe
Pontiac Sunfire
Door Panels and Handles
Ford Expedition XLT

How do you take a door panel off of a 1995 Pontiac Sunfire?

242526

Top Answer
User Avatar
Wiki User
2011-09-12 22:18:26
2011-09-12 22:18:26

i can answer this as i have alread done this. NOTE: these are instructions for a sunfire withOUT power windows/locks, if you have power w/l the steps are similar.

you must remove the screws along the bottom of the door panel. you must remove 2 screw in under the door "arm rest" (they're toward the front) you MUST remove the metal clip behind the window crank (those with pwr w/l don't have to worry about this step obviously) to do this: you can try to use a thin towel. placing it between the panel and the thin black disc and pulling in a teeter-totter motion. HOWEVER, the best and easiest way to do this is to get ahold of the tool made to do this. it can be picked up at most local auto stores. Or if you live near a best buy or other stores that does installations, tell them you are having trouble getting them out and ask them to remove them for you. (they have a Snap-On tool for this and it works like a CHARM!!) once the metal clip is removed pull the window crank off once you have the bolts and screws removed, you need to go along the edges of the door panel with a long screw driver or your hands and separate the panel fromm the door (there are several push-pin that hold it to the door) then lift up and out slowly. you'll have to move it around the door handle. before you try to complete take the panel off, UNHOOK the speaker wiring (and power doors/locks if you have them)

to put the panel back on, basically repeat the steps. the first thing you need to do is put the panel back on by starting at the top where the window comes out. there should be a groove that the door rests on. then line up all of the push-pins with their holes (and connect any needed wires) put the bolts back in under the arm rest, and along the bottom of the panel, then the window clip. (this may take a few attempts, but you'll get it)

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

No only 1995-2004 will work Pontiac sunfire doors from 95-04 will work also but the door moulding and door panel will need to be changed

User Avatar

there is screws around the door panel and the right under the handle there is 2 of them then your door is off hope this helps you :)

User Avatar

The fuse panel is located in the side of the dash where the driver's door closes against it

User Avatar

I can't tell you precisely, but you'll see it when you pull the inside door panel off to access it.

User Avatar

Not positive on your model, but open the driver's side door and look at the end of the dashboard. There should be a little access panel.

User Avatar

usually on the driver side door

User Avatar

When you open the passenger side door ... there is a pop out panel on the side of the dash where the dash meets the door.

User Avatar

You need to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.

User Avatar

The side of the driver's door on my 2002 Pontiac sunfire is a little hard to read, but I believe it says 30 PSI.

User Avatar

How do I remove the left side door panel of a 1995 Gmc Sierra without breaking the door panel?

User Avatar

* Pull the inside door handle to the open position and carefully pry the upper edge of the handle bezel out of the door trim panel with a flat-blade screwdriver.Lift the bezel upward and remove it from the trim panel.On front doors flip it over and unplug the electrical connector from the power door lock switch.Remove the bezel from the trim panel * Remove the window regulator handle * Remove the trim panel screws * Once all screws are removed detach the trim panel from the door disconnect any electrical connectors and remove the trim panel from the car by lifting it up and away from the door

User Avatar

How to remove left inner door panel of a Pontiac Bonneville 1996

User Avatar

The fuse panel in a Pontiac Montana is located in the passenger door. It is located on the same level as the glove box.

User Avatar

the door panel has a few clips on it that just snap in

User Avatar

The 2002 Pontiac Bonneville rear door panel is held in place by eight retaining clips and two screws. Remove the screws that can be found near the door handle. Pry outward on each retaining clip to remove the door panel.

User Avatar

remove front door panel 1995 Nissan maxima

User Avatar

You can GOOGLE Pontiac Door Lock and find a lot of hits. Try this one; http://www2.partstrain.com/store/ FriPilot

User Avatar

The 2006 Pontiac door panel is held in place by eight retaining clips. Pry outward on each retaining clip. A retaining screws near the door handle will also need to be removed.

User Avatar

split the fob halfs and the battery will be on the backside of the board!

User Avatar

You must first remove the trunk door facia. (This is the part with the "Pontiac" lights in it.) Then you can get to the bulb to replace it.

User Avatar

If only re-gluing vinyl to the door panel, use silicone. Do not glue the panel to the door.

User Avatar

The 1997 Pontiac Sunfire front bumper is held in place by six retaining clips and for retaining bolts. Remove the retaining bolts and pry outward on each retaining clip.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.