0
How do you take off the cap that is plastic and glue on to the drain pipe?
Wiki User
∙ 11y ago
There are different types of 'cap' that are plastic and glued to the drainpipe. If this is under the kitchen sink, and is a 'p' trap, then the plastic nut either side of it will unscrew with a pair of channel lock pliers or a small pipe wrench. If, on the other hand this is a 'cleanout' cap on the end of a drainpipe, then there will be a 'nut' formed into the end of it. Turn this nut with a wrench to remove it. Have shallow bowl or small bucket ready to catch water from this.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is the temperature rating of plastic drain pipe?
Buna-N8 200 deg f PVDF 250 F PP 80 deg f EPT 210 deg LDPE 140 VITON 185 HDPE 185 degGive or take depending what the medium is
What is wrong if the sink and the bathtub will drain but the toilet wont flush?
The toilet itself is plugged or the pipe from the toilet to the drain is plugged. It may be that the tub and sink have their own drain pipe that may connect to the main away from the toilet drain. Plunge the toilet or sometimes if you fill a 5 gallon bucket with water and pour it into the toilet as fast as it will take it, that will flush out the line. It is a greater amount of water all at once an forces out what the clog is.
P-trap replacement metal drain pipe from wall has swivel flange but missing slip nut. Is there a special way to still use this pipe as is with a new plastic or metal trap?
you can use a rubber connector with two "O"ring which are usually attached to the rubber. so you take rubber connection and slip it on the P tighting it and then do the same with the other side should work cost about $ 2.50
What does take off of pipe mean?
No
What is the take off for a six pipe?
6"
Do they make a glue for black plastic pipe and grey bard fitting?
Black plastic pipe is ABS -Use yellow ABS cement. -I don't understand "grey bard fitting" -Take this to your plumbing store and they will advise.Black plastic pipe is ABS -Use yellow ABS cement. -I don't understand "grey bard fitting" -Take this to your plumbing store and they will advise.
What is the hottest water a plastic PVC pipe can withstand?
PVC can take hot water like any other pipe but the reason no one wants to use it on hot water lines is because the glue joints can not take hot water so if your talking about straight pipe then it will be ale to take 212 degrees but if your talking about pipe and glue joints then it will fail around 65 + degrees F . If you want to run hot water in PVC you can use CPVC and the glue joints an pipe can with strand 212 degrees F but after some years as I have seen the pipe gets real brittle and so i always recommend the best called Wirsbo or any class AA pex
How long does it take abs pipe glue to dry?
It depeds whatANS 2 -ABS pipe glue dries in about 25 min to half an hour, cures almost totally in 4 hours/
How do they make tape sticky?
they take plastic and on the non-sticky side they glue on sticky-back-plastic
How long does PVC glue take to dry?
A PVC pipe glue will take at least 4 hours to dry. 12 hours before putting water pressure in it.
Why does tape leave residue?
Tape is pretty much plastic with some glue on it. Its the glue that sticks to the item you're taping, so when you take that tape off, the glue will normally stay.
How long does it take a plumber to find a drain pipe outside?
About 10 minutes if they know what they are doing
Do you use PVC pipe cement when connecting to a PVC pipe thread?
Use teflon tape with a little pipe dope. If you don't ever have to take apart again then you can use glue which you are calling cement
How do you clean trane Air conditioning drain lines?
If you're referring to drain lines coming from the drip pan beneath the air handler (the one inside the house), then just take some bleach water and pour it in the drip pan and it'll flow down the pipe and clean. If you're referring to another drain line coming from the machine itself, go ahead and cut off the pipe and replace it with a new pipe. Make sure you know what you're doing. It's PVC pipe, so use appropriate PVC glue and elbow joints. For best results, call your installation professional.
How do you solder a closet flange to a lead drain pipe?
I would take out the lead bend and replace it with pvc.
How do you make an H2O tail?
you take scles like plastic pieces and glue them toghether then ad a folder
What is the best type of glue to use on warhammer 40k assembly?
In my personal opinion I use a glue called "Zap-a-gap" it works well on both pewter and plastic models, and unlike plastic glue it doesn't melt the plastic together in case you wanted to take it apart for another model. Most people however will use a plastic glue (for plastic models of course) and a super glue (for pewter models). For basing the model, once I put the larger things like rocks etc. I use a weaker glue like Elmer's school glue on an old paint brush and coat whatever I wanted based in the glue. Then I put the model in the basing material (modeling grass, dirt, sand, etc) and gently blow the extra off. Hope that helps
