answersLogoWhite

0


Best Answer

There are many factors involved with wiring a rocker switch in a car. These factors include how many prongs the rocker switch has, whether it is an SPST or SPTD, and others. The most difficult part is knowing where to place the prongs on the vehicle. This can be done by using a multimeter.

User Avatar

Wiki User

9y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

12y ago

its not as hard as you may think u can eather get an addapter from the store that will be labled like your car and you plug it in and match the wires or you can hard wire it in

red- power

yellow- memmory

black- grond

blue- remoate

thoes are all the same everytime....

then you will have 4 sets of wires in each set there the same color but 1 has a black like on it that one is negative and the onle that's the same color is the positive

normally there is a wireing diagram on the raideo that will tell you witch is the fron and witch s the rear speaker wires .........just hook them up and your done

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you wire a rocker switch in a car?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Can i have an electric rocker switch in the wet room?

can i have an electric rocker switch in the bathroom


How to turn on my head light and tail lights with no switch?

For Temporary Fix, By A Rocker Switch From Auto Parts Store. Pull Your Head Light Switch Out Of The Dash Wire In The Rocker Switch. Will Have To Find Wiring Diagram Or Chiltons Book For Wiring Schematic For That Year Of Vehicle. Only Temp Fix, Should Replace With Stock Switch For That Vehicle.


What happens when you switch the red wire and yellow wire round on a car stereo?

Nothing.


How do you wire a cable with a black wire a brown wire grey wire and earth wire to a light switch in my car which has 3 holes 1 for single switch and 1 for a doubleswitch?

See discuss question below.


How do you wire in a toggle switch to start the car?

By passkey. If you are talking about a starter by-pass. It is not keyed, but a push button on & off switch. You must break the small wire at the starter relay, or solenoid, and wire the switch in series. After the car starts, you must release the push on/off switch, or you will keep turning the starter motor.


How do you switch on parking lights?

The rocker switch on top of the steering column.


How do you wire a rocker switch to radiator fan on a Grand Am?

to shut the fans on and off by yourself. remove the connector for the wires at the fan. hook a wire from the positive on fan motor to the inside toggle switch, do not hook to switch yet. run a wire from the positive on battery, hook to battery after hooking up switch. hook up the wires to the switch. then the battery. its up to you if you want to install a 15 amp fuse in line from battery to toggle switch.. you can also get the power from the fuse box instead of the battery. this should work for you. if not you may need to ground the other fan wire.


How do you pull a wire from ignition switch to connect a off market stereo for a 2002 Chevy cavalier it does not have the ignition switch wire?

i do not know go to a car stereo install ... store


What is the meaning of rocker switch?

A rocker switch is a type of switch (i.e. light) that rocks when switched, rather than trips like the majority of switches. The side of the switch not in use will be raised, while the active side will be pressed down.


How do you disable an ignition kill switch?

If I remember correctly, an ignition "Kill Switch" is a secret switch (or button) that must be pushed into a particular position for the ignition system to start the car.... That being said.... Simple. If it's a button that has to be pressed for the (key) ignition to start the car, duct tape it in place. Same for a "light switch" switch". OR...you could solder a wire to circumvent the switch..... :) Now remember...if the switch uses a thicker wire....you're going to want to use a thicker wire when you solder it :)


How do you switch from two wire alternator to a one wire alternator?

The switch will depend on the alternators and car wiring. The switch could require removing an external regulator as well. You will need a wiring diagram of the vehicle wiring to decide which wires to change.


Replaced starter and battery both battery and starter work after tests car wont start stillfound that a purple wire that goes to the starter is getting no power what could be the problem?

purple wire comes from park netural switch .yellow wire come from ingintion switch to park netural switch