answersLogoWhite

0

  • Ford Ranger
  • Ford Ranger XL
  • Ford Ranger XLT

How does a holes come off a 1993 ford ranger slave cylinder?

User Avatar

Wiki User

βˆ™ 2006-08-20 04:25:38

Best Answer
Copy

You drive the cold roll pin out, BUT if planning on replacing slave cyl, replacing the master line and slave as a unit is recommended more often then not there will be a leak when replacing line.

2006-08-20 04:25:38
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Add your answer:

Earn +5 pts
Q: How does a holes come off a 1993 ford ranger slave cylinder?
Write your answer...
Submit

Related Questions

How do you fix a slave cylinder in a 1993 ford ranger?

you just need to hone it out and replace parts with rebuild kit.


Where is the clutch slave cylinder on a 1993 ford ranger 4x4?

I believe that is inside the manual transmission bell housing


Where is the the bleed valve on a slave cylinder on a 1993 ford ranger?

The bleed valve is located on the drivers side of the bell housing.


Where is the Jeep Wrangler slave cylinder?

how to replace the slave cylinder on a 1993 jeep wrangler


How do you change internal slave cylinder to an external slave cylinder on a 1993 wrangler?

no none of the answers were my question


How do I attach the cable from master cylinder to the slave cylinder in a 1993 Ford Ranger?

the master and slave cylinder are a built in unit,there is no cable between them. there are piston'fluid connected. you can buy a rebuild kit for $9.00. But it is much better to buy a rebuilt master cylinder than try to rebuild it. Especially on ABS master cyclinders.


Is the clutch in the 1993 ford ranger a hydraulic clutch?

yes it is with the slave cylinder being inside the bee housing. the clutch master cylinder reservior is to the right facing the firewall. it requires brake fluid


Do you have to replace the master cylider if the slave cylinder has been replaced in a 1993 Saturn?

The Slave Cylinder and the Master Cylinder control totally different systems. The Slave has to do with the clutch, and the Master has to do with the brakes. They have nothing in common.


Does a 1993 2.3 Ford Ranger have a non-interference engine?

Yes , the 2.3 liter 4 cylinder in a 1993 Ford Ranger is a non-interference engine


How much does a 1993 Ford Ranger 4-cylinder gas tank hold in gallons?

I have a '93 Ford Explorer and it hold 19 gallons From the Chilton Ford Ranger guide: "1993 Ranger with standard wheelbase: 16.3 1993 Ranger with long wheelbase: 19.6"


How do you add brake fluid to the slave cylinder in a 1993 Escort?

You don't. You add it to the master cylinder and bleed the brakes.


Where is clutch slave cylinder 1993 rx7?

Bolted to the transmission underneath the car


How do you bleed the slave cylinder on a 1993 Jeep Wrangler?

Right above the slave cylinder there is a bleeder screw. Just unsrew it and have someone hold in the clutch to start the bleed.


What size motor is in a 93 Ford Ranger xlt four cylinder two wheel drive five speed?

The 4 cylinder in a 1993 Ford Ranger is 2.3 liter ( 140 cubic inches )


How and where do you change a slave cylinder for a 1993 Chevy S10 manual pick up?

The slave cylinder on my s10 in on the driver side of the transmision. There are only 2 nuts that have to be removed to take the slave cylinder off. Then u must take out the pins to remove the clutch line.. Hope this helps


Where is the clutch bleeder valve on a 1993 Saturn sl2?

It SHOULD be on the clutch slave cylinder. Follow the hydraulic line from the clutch master cylinder down to the slave cylinder. Depending on the vehicle, it could be behind the dust cover of the bell housing.


What holds the clutch fork on a 1993 Chevrolet 1500 bellhouseing?

A 1993 does not have a clutch fork if it is a pick-up truck. It has an hydraulic slave cylinder.


How do you remove the pin from the clutch line at the slave cylinder on a 1993 Chevy Z71?

you must drive the roll pin out where the line goes into the slave cylinder its a real small pin. can use a small punch or nail to remove.


Can you bleed a slave cylinder on a 1993 Saturn?

Yes. However it is very tricky. Refer to saturnfans.com for a full procedure


Will a 4 cylinder 1993 mustang transmission mount to a ford ranger transfer case?

no,output shaft is too long


Can you use a transmission from a 1993 Ford Ranger to a 2000 ranger?

can you use a transmission from a 1993 ford ranger in a 2000 ford ranger?


Where is the slave cylinder on a 1993 Ford Probe?

many 93 ford probes have the slave cylinder and the brake pump as one. ford had a great idea of putting those two together. its the drivers side off in the back right by the wheel base.


Does a 93 ranger have a timing belt or chain?

In a 1993 Ford Ranger : The 2.3 liter four cylinder engine has a timing BELT and The 3.0 and 4.0 liter V6 engines have a timing CHAIN


How do you change a 1993 Ford Ranger clutch?

how to i change a clutch in a 1993 ford ranger


What direction does the rotor cap for a 1993 Ford Ranger 30 6 cylinder rotate?

The rotor inside the distributor cap turns CLOCKWISE