answersLogoWhite

0


Best Answer
Copy
Removing grillTo remove the center grill, you must first remove both of the headlight fascia, which each have two small recessed Phillips head screws at the top right and left corners and who overlap the side tabs of the grill face plate.

Once undone, the headlight fascia tilt forward and come away - taking care not to damage the tabs at the bottom which sit in the slots of the surround.

With the headlight fascia removed, you can then remove the 4 flanged Phillips head screws which hold the grill faceplate on. Once those screws are removed, the grill faceplate will also tilt forward.

Tilt it forward and lift vertically.

Installation is done in reverse, grill face plate first.

User Avatar

Wiki User

โˆ™ 2011-09-12 21:52:36
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How does one completely remove the grill from a 2000 Jeep Cherokee Sport after taking out the screws?
Write your answer...
Submit

Related Questions

How do you change the headlight on an 88 Honda accord?

# Disconnect negative battery cable # Remove the retaining screws and detach the headlight bezel # Remove the headlight retainer screws taking care not to disturb the adjusting screws # Remove the retainer and pull the headlight out enough to allow the connector to be unplugged # Remove headlight now # Disconnect negative battery cable # Remove the retaining screws and detach the headlight bezel # Remove the headlight retainer screws taking care not to disturb the adjusting screws # Remove the retainer and pull the headlight out enough to allow the connector to be unplugged # Remove headlight now


How do you remove the shift lever in a 96 b3000?

Remove the rubber boot by taking out the 4 Philips screws in the pastic base then lift it off. the boot is attached to the plastic. Then pull the next rubber mat up enough to get to the 3 torx screws, These are what holds the shifter in. MAKE SURE THE VEHICAL IS IN NEUTRAL. Remove the screws and lift the shifter out. Remove the rubber boot by taking out the 4 Philips screws in the pastic base then lift it off. the boot is attached to the plastic. Then pull the next rubber mat up enough to get to the 3 torx screws, These are what holds the shifter in. MAKE SURE THE VEHICAL IS IN NEUTRAL. Remove the screws and lift the shifter out.


How do you remove the headlight in a 1989 Honda accord?

On retractable headlight models raise the headlightsDisconnect the neagative battery cableRemove the retaining screws taking care not to disturb the adjustment screwsRemove the retainer and pull the headlight out enough to allow the connector to be unplugedRemove the headlightTo install the headlight plug the connector in place the headlight in position and install the retainer screws tighten the screws securleyPlace the headlight bezel in position and install the retaining screws


How much does it cost to remove drywall?

Depends what you know. Some people can remove it quickly by taking out 3-4 of the top screws and then prying it out carefully with a crowbar.


How do you remove glove box in 1998 Toyota sienna need to change the cabin air filter?

remove the glove box by taking out the screws facing you. then pull it down


How do you change a headlight on a 1987 Honda Accord?

On retractable headlight models raise the headlightsDisconnect the neagative battery cableRemove the retaining screws taking care not to disturb the adjustment screwsRemove the retainer and pull the headlight out enough to allow the connector to be unplugedRemove the headlightTo install the headlight plug the connector in place the headlight in position and install the retainer screws tighten the screws securleyPlace the headlight bezel in position and install the retaining screws


Rreplace headlight on 1989 Honda accord?

On retractable headlight models raise the headlightsDisconnect the neagative battery cableRemove the retaining screws taking care not to disturb the adjustment screwsRemove the retainer and pull the headlight out enough to allow the connector to be unplugedRemove the headlightTo install the headlight plug the connector in place the headlight in position and install the retainer screws tighten the screws securleyPlace the headlight bezel in position and install the retaining screws


How do you replace a headlight in 1989 Honda Accord?

On retractable headlight models raise the headlightsDisconnect the neagative battery cableRemove the retaining screws taking care not to disturb the adjustment screwsRemove the retainer and pull the headlight out enough to allow the connector to be unplugedRemove the headlightTo install the headlight plug the connector in place the headlight in position and install the retainer screws tighten the screws securleyPlace the headlight bezel in position and install the retaining screws


How do you remove 1995 jeep yj stereo?

1) Have you tried taking the front dash off and checking the install underneath? I know my comes off easily (6 screws) and then the stereo was mounted with a few screws under that. 2) If you do successfully remove the stereo and it still works I may be interested in taking it off your hands :)


How do you remove the the dash board from a 1995 Volkswagen Jetta?

Start by taking the vents out Then the airbag light spot and then ull see screws


How do you remove a spark resistor from a 1990 Honda four tr-ax four wheeler?

you remove the spark arrestor by taking the little screws that are at the end of the tip then yank it out with pliers


How do you remove the front licence plate cover on a 2000 Pontiac Firebird?

Under the cover there should be two screws. On my '02 Firebird they were a star screw. Taking those two screws off let the panel come out.


How do you remove the center console from a 1999 trans am?

open the console door and start taking out screws in the base and then there should be a couple of screws under that console door that hold the top of the console on, take them out and then when you lift the top of the console up you will see all the screws that hold it to the floor.


Where is the ecm on a 1996 olds ciera?

It is located directly on the firewall behind the glove box. It is easier to remove with less chance of damaging the ecm holder if you remove the screws on the front of the glove box, the screw holding the glove box retaining cable, and the bottom screws holding up the bottom cover just below the glove box. This will be easy since all of the screws are 7mm screws. The screws that hold the pins onto the ecm are also 7mm. You will then remove the ecm from the bottom but by taking the glove box out you can actually see what you are doing.


Is their insurance for someone who cosigns a loan?

No. The co-signer is taking on the risk completely on their own.No. The co-signer is taking on the risk completely on their own.No. The co-signer is taking on the risk completely on their own.No. The co-signer is taking on the risk completely on their own.


How do you replace headlight assembly for 2006 jetta?

To replace the headlight assembly on a 2006 Jetta, remove the front grill. Then remove the headlight assembly by taking off the screws that secure it in place. Replace with new.Ê


How do you remove the headlight switch on a 2001 impala I made the mistake of taking out the two screws and now it is in pieces with one brass piece missing Help please Randy?

To remove the head light switch you need to remove the bottom of the dash ... their are 2 screws at the bottom as soon as those are done the rest are just clips so u pop it out


How do you replace crankshaft position sensor on a 1988 olds 98?

To replace the crank sensor you have to remove the harmonic balance taking special attention not to damage the pulley or the cam shaft. Remove the two 10mm retaining screws


How do I remove center console parts on 1998 eclipse?

u can remove the center console by first taking out the plastic cover around the ac and stereo. then u open the cup holder and pull it up to remove that whole piece. underneath that u will find two screws that need to be taken out along with two other screws on the side of the console that you will not find unless ur seats are folded forward. once that is done u can remove the center console. u can remove the center console by first taking out the plastic cover around the ac and stereo. then u open the cup holder and pull it up to remove that whole piece. underneath that u will find two screws that need to be taken out along with two other screws on the side of the console that you will not find unless ur seats are folded forward. once that is done u can remove the center console.


Who tried to stop the US government from taking over Cherokee lands by taking his case to the Supreme Court?

Leader of the Cherokee Nation's government, Chief John Ross.


While taking out screws that allow you to remove brake caliper one broke off half way is their anyway that you can still remove that so you can take off caliper?

Youll probably have to drill it out and get a new bolt to mount the caliper with.


How do you replace lift gate struts on a 1994 Jeep Grand Cherokee?

There is an eyelet at one end, not a clip, how do I get that off. Should be clips at each end of struts- - slide them back and strut will come pop off of stationary pins I have a 1993 Jeep grand Cherokee i bought new struts from autozone about 20 bucks attached to the lift gate there are 2 screws and attached to the body by near the taillight there is a ball with a pin holding it on, pull the pin out then pull the strut off. the remove the screws attached to the lift gate. have a stick or something to hold up the lift gate when you are taking these off....


Taking off seat for a 1996 Yamaha virago?

There are two ten mm screws below the widest part of the seat, remove them. Lift the back and pull to the rear to unhook the front.


How do you change the Fuel filler door on a 2003 Pontiac?

Remove the fuel cap on the 2003 Pontiac. Remove the plastic cover around the filler pipe by taking the two screws out. Under the plastic there are two nuts that hold the door and hinge assembly on. Remove them and the door will come off.


How do you remove tail light assembly from 2004 suburban?

The tail light assembly on a 2004 Chevy Suburban can be removed by taking out the retaining screws and twisting the bulb assembly. The assembly can then be pulled from the vehicle.