We need you to answer this question!
If you know the answer to this question, please register to join our limited beta program and start the conversation right now!
Asked in Geo Metro
How do you Drill front bumber for license plate on 97 metro geo?
try using a drill motor and a drill bit
Asked in Chrysler Concorde
How do you change a headlight bulb on 2002 Chrysler Concorde?
The headlamp bulb is removed from the rear of the headlight assembly. You have to remove the front bumber fascia to remove the headlamp assembly on this model. There is a plug that needs to be removed (twist one way, then pull) and the bulb should come out with it. Installation is reverse of removal. see the link below for more on removing te bumper to access the headlight. ...
Asked in Chevy Silverado
Where are the impact sensors on 1997 Silverado?
They are mounted on the front of the truck in behind the bumber. The air bag sensors will be the only sensors that have a YELLOW wire connector pluged into them. Just craw in under the front bumber and start looking all up in the front body parts behind the bumber and grill. You will see THEM. ...
Asked in Car Horns, Ford Falcon
Where is the horn located on a Xh Ford Falcon ute?
tucked in behind the front bumber bar. in front of the a/c condenser
Asked in Radiators, Nissan 300ZX, VW New Beetle
1985 300ZX needs new radiator does the front bumber need to be removed to accomplish this and should it take a mechanic 3 hours?
== == No and No. The radiator can easily be replaced without touching the front bumper. It may take 3 hours, but it shouldn't take a professional that long. ...
How do you change the front signal light bulb on a 1993 Pontiac Grand AM?
underneith the front bumber twist counter clockwise replace bulb
Asked in Chevy Venture
How do you replace a front wheel bearing on a 2003 Chevy Venture?
To replace the front bearing,jack up front and remove the wheel.Remove the brake caliber assembly and pads.The brake caliber guide ,held in place by 2 bolts that is bolted to the hub assembly has to be removed in order to remove the rotor.Remove the 3 bolts which hold the wheel bearing to the hub assembly,from the backside.Remove the 35mm axle nut using an inpact drill or strong arm.Tap the axle out of the assembly and the bearing assembly should come out from...
Where is oil drain plug and oil filter located in 2002 Blazer?
The oil drain plug is screewed into the bottom side of the oil pan. The oil filter is in behind the front bumber. Slide in under the front bumber and look up and you will see an plastic cover that you will have to remove to get to the oil filter. ...
Asked in Cars & Vehicles
Change headlight 2004chevy's s10?
Open the hood, stand in front of headlight assembly, notice two black tabs sticking up behind assembly in back of the radiator support. Wiggle the tabs up and off, these tabs lock the headlight assembly into the radiator support. Once the tabs are removed you can wiggle the assembly out the front and gain access to the bulbs. Install in reverse. ...
Asked in Ford Trucks and SUVs, Ford F-150
How do you replace the front parking light on a 2003 ford f150?
There is a single screw above each front parking light assembly. You will need a 7mm socket to remove the screw. After the screw is removed, simply pull on the assembly from the back corner and pull straight forward. ...
Asked in Cars & Vehicles
What years interchange with a 2002 Dodge Ram 1500?
what year interchange with a 2002 dodge ram 1500 front bumber
Asked in Chevy Tahoe
Where is the front impact sensor on a 2003 Chevy Tahoe?
There should be 2 maybe 3 in behind the front bumber somewhere. Just look for YELLOW plug connectors. ...
Asked in Dodge Durango
How do you remove the oil pan on a 1998 Dodge Durango?
If it is four wheel drive, the front axle assembly will need removed to access the oil pan. ...
Asked in Suzuki Samurai, Samurai
How do I install larger wheels on samurai?
Well the only size you can run are 235/75 on a 15 in stock rim I have BFGoodrich A/T KO had to trim the bumper bracket only because it got hit in the front but the other front doesn't rub...if you want 30's you'd have to cut of the ends to the bumber bracket behind the bumber but then you lose your bumber and turn signals. You do lose articulation when you go up in size with out a lift...
Asked in Bahamas
Whose statue is in the front of the house of assembly in the Bahamas?
Queen Victoria's statue is in front of the House of Assembly.
Asked in Jeep Cherokee, Jeep Cherokee Sport, Jeep Grand Cherokee Laredo, Jeep Grand Cherokee Limited
Where is the horn located on a 1993 Jeep Cherokee?
Its located behind the front bumber on the drivers side. Under the turn signal lamp. ...
Asked in Geo Metro
How do you remove the seat headrest in a Geo Metro?
Press into the fabric of the seat, immediately in front of the base of the headrest. This will release the catch, and the headrest can be adjusted up or down, or removed entirely from the seat. ...
How do you change the front signal bulb in the front bumper of a 1996 cavalier?
I have a 1998 Cavalier and I couldn't figure it out until I watched my mechanic do it:) The headlight assembly has to come completely off, and then down below that, you will see the signal light assembly. To get the headlight assembly off, there should be some screws under neath the plastic housing that has to be removed first, Undo the screws ad presto:) ...
How do you replace the headlights on a 2002 Oldsmobile Bravada?
Each of the headlight assemblies are braced through the radiator support with a pair of retainers. The retainers for the right headlight assembly are in front of the battery. The retainers for the left assembly are in front of the washer fluid reservoir. Remove the retainers by pulling up on the retainer. With the retainers removed, the headlamp assembly falls forward. Reinstall the retainers to the square tabs on the headlamp assembly and the rivet on the radiator support ...