Best Answer

three bolts, make sure the battery is disconnected first!gmjim

User Avatar

Wiki User

โˆ™ 2005-09-17 22:25:17
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How many bolts are there to take out on an 1993 Mercury Sable starter?
Write your answer...
Related questions

How do you replace a starter in a 1993 mercury capri?

Remove the positive cable from your 1993 Mercury battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install your new starter.

How do you know when the starter on a 1993 Mercury Sable has gone out?

The first clue would be if the car doesn't turn over :)

What is a pcm on a 1993 mercury sable?

PCM stands for Powertrain Control Module on a Mercury Sable

How do you remove a starter on a 1993 Mercury Topaz?

Disconnect - battery cable Loosen 2 mounting bolts Remove wiring Drop starter

Where is the location of the computer for 1993 LS Mercury Sable?

the computer for a 1993 ls mercury sable is by the top of the engine on the pasinger side a black box is on it you only have to unplug it

Where is the starter located on a 1993 Mercury Grand Marquis?

where is the starter located for 1993 grand marquis It is on the passenger side of the car and it is a pain in the butt to get the top 2 bolts off so good luck

Where is the starter solenoid on a 1993 Mercury Villager?

On the starter.

How do you test the starter solenoid for a 1993 Mercury Sable?

I had to do this too, you take it to Autozone an they'll test it for you because I had to replace the same on mine. So hope that helps

What size bolts holds in a starter for an F250?

What size starter bolts for an 1993 Ford F250 4x4 automatic

Your horn has been sounding by itself on your sable wagon?

where is the horn relay on my 1993 Mercury Sable located

How many wires go to the starter relay on a 1993 mercury topaz?

there are 5 wires that go to the starter relay on a 1993 mercury topaz

Where is obd2 on 1993 Mercury Sable?

It's too old to have OBDII -_-"

What is the right Tire pressure for 1993 Mercury Sable?

The right tire pressure for a 1993 Mercury Sable is between 33 and 36 psi. Correct tire pressure will save you in gasoline cost over time.

Where do you put motor oil in the engine of a 1993 Mercury Sable? the engine?

Where is the fuel pump on a 1993 Mercury Sable?

Mounted on top and inside the fuel tank.

How many mounting bolts are there on the starter of a 1993 Acura Integra?


When you tried to start your car it just made clickingng noise 1993 mercury sable the head lights didnt dim when i tried to start the car?

It could be a weak battery. The starter solenoid may be defective. If so a rebuilt starter could cure the problem.

What size bolts hold up the starter on a 1993 thunderbird V8 5.0?

Starters on a 1993 Thunderbird have bolts sizes not listed online. However, inexpensive starter bolt sets may be purchased from specialized online retailers.

How do you install a starter on a 1993 Chevy Corsica?

Begin by removing the positive cable from your 1993 Chevy Corsica battery. Remove the cables on the front of the starter. Remove the starter retaining bolts. Reverse the process to install your new starter.

Where is the backup light switch on a 93 mercury sable?

The 1993 Mercury Sable backup light relay switch can be found beneath the drivers side dashboard. The backup light relay switch will be above the accelerator pedal.

How many gallons does a 1993 Mercury Sable with V6 3.8 meter engine have?

i think 16 gallons

How do you put brake fluid in 1993 Mercury Sable?

Master cylinder - located at drivers side firewall

Where is the location of the hazard flasher for 1993 Mercury Sable?

On top of the steering column. top of the steering wheel

Why wont the Brakes bleed 1993 Mercury Sable?

did you replace the master cylinder if so it has to be bleed frist

How many bolts do you have to take off to remove the starter from a 1993 Pontiac Bonneville?


Study guides

Create a Study Guide