answersLogoWhite

0

  • Fuel Pumps
  • Chevy Blazer
  • Chevy Blazer S-10

How much to replace and install fuel pump for 1993 Chevy blazer?

User Avatar

Wiki User

βˆ™ 2010-09-25 05:00:40

Best Answer
Copy

About 250$ for the pump at AutoZone or O'Riley's Auto parts (If you have one) Installing isn't too complicated, unless it's your first time. Be sure to follow ALL directions EXACTLY and don't skip ANYTHING. Lookup 'install fuel pump' and whatever make/model/year said car is, and e-how should pop up. Good luck!

2010-09-25 05:00:40
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Add your answer:

Earn +5 pts
Q: How much to replace and install fuel pump for 1993 Chevy blazer?
Write your answer...
Submit

Related Questions

How do you repair a throttle cable for 1993 Chevy S10 blazer?

Replace it with a new one, there is no repairing it.


Where is the horn located on a 1991 Chevy Blazer?

Where is the horn located on a 1993 chevy blazer


How to replace a 1993 Chevy blazer full size exterior door handle?

You will need to remove the inside door panel of your 1993 Chevrolet Blazer. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install the new door handle.


What causes a 1993 s10 Chevy blazer to stall while driving?

Need to replace the ingnetion module in the distributor.


How do you install the fan belt on a 1993 Chevy S10?

how do you replace fan belt on 95 Chevy S-10 2.2 engine


How much does a 1993 Chevy Blazer weigh?

3500


How do you replace spark plug wires on a 1993 Chevy S10 Blazer?

One at a time so as not to mess up the firing order.


Are 1993 Chevy Tahoe doors interchangeable with 1987 Chevy Blazer doors?

yes they are


How do you change an ignition module in a 1993 Chevy blazer?

your a fatty


Are most parts on a 1993 GMC Jimmy compatible with a 1993 Chevy Blazer?

yes it is


Does a 1993 Chevy S10 Blazer have a Inertia switch If so where is it?

None


What would make my dashboard lights not work in my 1993 Chevy blazer Tahoe?

A blown fuse can make your dashboard lights to not work in your 1993 Chevy Blazer Tahoe. A burned out bulb can also cause this.


What is the towing capacity for 1993 4x4 Chevy Blazer 350 Silverado 1500?

if its a full size blazer 7000lbs


Where is the fuel pump fuse located on a 93 S10 Blazer?

which fuse is for the fuel pump in a 1993 chevy s10 blazer


What size is the dash speaker of a 1993 Chevy blazer?

4x6 in the front dash


What does the abbreviations CTSY stand for in the fuse box of a 1993 Chevy blazer?

courtesy


How to replace alternator in 1993 Chevy G20?

Remove the belt from your 1993 Chevy G 20 alternator. Remove the alternator wiring harness. Remove the retaining bolts from the alternator. Reverse the process to install the new alternator.


How do you install a heater coil in a 1993 full size Chevy Blazer 4 wheel drive?

I found the answer on AutoZone.com There was a section on repair info and then go to Heater Core GM Blazer/Jimmy/Typhoon/Bravada 1983-1993 Repair Guide. It has a detailed guide and pictures. Good Luck!


How do you replace the ignition module on a 1993 Chevrolet Blazer?

Find your distributor cap and follow the center cable to a rectangular part. This is the ignition module. Remove it, get a new one and install it.


How do you find Diagrams for a 1993 Chevy S-10 Blazer?

the delership or library


Where is the transfer case control module in a 1993 Chevy blazer?

That year did not have a controll module.


Where is the IAT sensor on a 93 Chevy s10 blazer?

The 1993 Chevy S 10 Blazer IAT sensor can be found on the top of the transmission. The IAT sensor will be near the front of the transmission.


Can the ECM be bypassed in a 1993 s10 blazer 4.3?

Is there a way to bypass the ECM in a 1993 chevy s10 4.3 vortec


How do you replace the starter on a 1993 Chevy Cheyenne?

Remove the positive battery cable from your 1993 Chevy Cheyenne battery. Remove the two cables from the front of the starter. Remove the three starter retaining bolts. Reverse the process to install the new starter.


Do you have to replace the hub on a 1993 Chevy k2500 if you need to replace the wheel bearing?

If, after close inspection you do not see any damage to hub, you can use it. But ALWAYS install new bearing race with bearing.