0
How tight do you tighten the rocker arm bolts on a 5.7 liter vortec engine?
Wiki User
∙ 11y ago
24 foot pounds
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Is a 1989 Chevrolet 350 a vortec motor?
I know on my vortec engine the valve cover bolts are in the center of the cover and there is only 4, my racecar has vortec heads and my truck has standard stock heads with four bolts on thew corners
What are the torque specs for the rocker arms arms on a 1993 ford escort with a 1.9 liter engine?
Odd that I would come across your question since ironically i just finished replacing my rocker arms :D The answer is tighten the bolts to 17-22 ft lb
How do you adjust valves on 90 Nissan Sentra?
Remove the valve cover. Tighten bolts next to rocker arms. done
What is the torque specifications for the intake manifold on a 1997 Chevrolet vortec 350?
Install the lower intake manifold to the engine. Apply sealer, GM P/N 1052080 or equivalent, to the lower intake manifold bolts.Install the lower intake manifold bolts. Tighten the bolts in three steps:TightenTighten the bolts on the first sequence to 8 N·m (71 lb in).Tighten the bolts on the second sequence to 12 N·m (106 lb in).Tighten the bolts on the final sequence to 15 N·m (11 lb ft).I this is what you are looking for.GMmechanic@gmail.com
What are the torque specs on the rocker arm bolts on a jeep 1984 cj7 with a 258 8 cylinder engine?
The 1984 258 cubic inch engine rocker arm bolt torque specification is 30 pounds. You should torque the rocker arm bolts in 15 pound intervals.
What are the torque specs for rocker arms on 97 31 Chevy motor?
Are we talking about a 1997 - 3.1L OHV engine here? If so, it's a two step operation. First step is tighten the bolts to 89 in-lbs Second step is rotate the bolts an additional 30-degrees. Make sure that as you're tightening the bolts that the pushrods are sitting properly in the rocker arms and that the tabs on the bottom of the rocker arm pedestals are seating properly in the grooves milled in the head.
What is the rocker arm torque specs and sequence for a Chevy 305?
With the valve fully closed and the lifter fully at the down position, tighten the adjusting nut until there is no up and down travel in the push rod. Then tighten the adjusting nut 1/4 turn. This is only if you have hydraulic lifters. Tighten the rocker studs to 50 ft/lb of torque. These are the bolts holding the rocker assembly in place.
What is the torque sequence for rocker arm bolts on a 1991 ford 1.9 engine?
There is no torque sequence just torque rocker arm studs to the proper torque
Where is the rockers bolt located on a 350 engine?
350's use rocker studs instead of bolts, and they are mounted to the heads.
What are the torque settings and tightening sequence for the rocker box bolts on a Harley Davidson shovelhead engine.?
The rocker box bolt torque specifications, on your Harley-Davidson, is 15 pounds per square inch. The bolts should be torqued in five pound intervals.
What are the torque settings and tightening sequence for the rocker box bolts on a Harley Davidson shovelhead engine?
The rocker box bolt torque specifications, on your Harley-Davidson, is 15 pounds per square inch. The bolts should be torqued in five pound intervals.
What are vortec heads?
the fastest way to tell is if the center intake bolts are not there.the vortec heads that everyone wants for performance have no center intake bolts.
