answersLogoWhite

0


Best Answer

first you need to drain the oil then you unbolt the motor mounts and lift the motor up as far as it will go. unbolt oil pan and drop down as far as it will go then reach your hand up and unbolt oil pump drop pump in pan and slide pan out. put new pump in pan and slide pan back in bolt oil pump back up and then put pan back on and bolt motor mounts back up.

User Avatar

Wiki User

โˆ™ 2015-07-16 18:29:52
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How to Install an oil pump in a 1988 Bronco?
Write your answer...
Submit
Related questions

How do you replace a oil pump on a 1988 iroc-z camaro?

You will need to drain the oil from your 1988 Chevrolet Camaro oil pan. Remove the oil pan retaining bolts. Remove the oil pump retaining bolts. Reverse the process to install the new oil pump.


Where is the oil sending unit on a full sized 1988 Ford Bronco?

It is on the driver side of the engine block next to the power steering pump.


Where is the oil pump located on a 1989 ford bronco?

The oil pump is bolted to the bottom of the engine , inside the oil pan


Where is the oil pump located at on a 1987 302 bronco?

The oil pump is bolted to the bottom of the engine , inside the oil pan


How do you install an oil pump in a 1977 F250?

Drain the oil from the oil pan. Remove the oil pan. Unbolt the old oil pump. Reverse the process to install the new oil pump.


Is mechanical or electrical the oil pump in a Ford Bronco 92?

mechanical - the oil pump is bolted to the bottom of the engine , inside the oil pan


How to install wirer oil pump?

No


How do you replace the oil pump in a 2001 dodge ram?

Remove the oil pan. The oil pump will be visible. Remove the retaining bolts from the oil pump. Reverse the process to install the new oil pump.


How do you replace oil pump on 2003 Chevy Malibu?

Remove the oil pan. The oil pump will be visible. Remove the oil pump pickup to. Remove the oil pump retaining bolts. Reverse the process to install the new oil pump.


How do you change oil pump on 97 Tahoe?

Drain the oil from the oil pan and remove it. Remove the oil pump retaining bolts. Reverse the process to install the new oil pump.


Where is the oil pump on a 2001 dodge stratus?

under the oil pan you have to take it off completely before you can install oil pump......


How do you change oil pump on 2001 ford f150 5.4 liter?

Oil PumpRemoval & Installation4.6L and 5.4L Engines1. Remove the timing chain.2. Remove the oil pan.3. Remove the three oil pump screen and cover bolts, then remove the screen and cover.4. Remove the oil pump screen and cover spacer.5. Remove the four oil pump mounting bolts, then remove the oil pump from the engine.To install:6. Clean and inspect the mating surfaces.7. Install the oil pump and loosely install the four oil pump mounting bolts. Tighten the four oil pump bolts in sequence to 71-106 inch lbs. (8-12 Nm).8. Install the oil screen and cover spacer to 15-22 ft. lbs. (20-30 Nm).9. Install the oil screen and cover, then install the three oil pump screen and cover bolts. Tighten the bolts near the oil pick up screen to 15-22 ft. lbs. (20-30 Nm) and the bolts at the opposite end of the pick-up to 70-106 inch lbs. (8-12 Nm).Install the timing chains, then install the oil pan.


How to replace oil pump on 2003 buick century?

Drain the oil from the oil pan. Remove the oil pan. Remove the oil pump retaining bolts. Reverse the process to install the new oil pump.


How do you change the oil pump in a 2007 escalade?

written instruction on how to install oil pump in 2007 cadillac escalade


What is the procedure for replacing the oil pan gasket on a GM 350?

for a 1988 gmc gm4 5.7 electric fuel pump on a typical sending unit. question is how to install it


How do you change the oil pump on a 2004 expedition?

Oil Pump Removal & Installation4.6L and 5.4L Engines1. Remove the timing chain. 2. Remove the oil pan. 3. Remove the three oil pump screen and cover bolts, then remove the screen and cover. 4. Remove the oil pump screen and cover spacer. 5. Remove the four oil pump mounting bolts, then remove the oil pump from the engine. To install: 6. Clean and inspect the mating surfaces. 7. Install the oil pump and loosely install the four oil pump mounting bolts. Tighten the four oil pump bolts in sequence to 71-106 inch lbs. (8-12 Nm). 8. Install the oil screen and cover spacer to 15-22 ft. lbs. (20-30 Nm). 9. Install the oil screen and cover, then install the three oil pump screen and cover bolts. Tighten the bolts near the oil pick up screen to 15-22 ft. lbs. (20-30 Nm) and the bolts at the opposite end of the pick-up to 70-106 inch lbs. (8-12 Nm). 10. Install the timing chains, then install the oil pan.


1997 f350 7.5l how to change an oil pump?

Oil Pump Removal & Installation4.6L and 5.4L Engines1. Remove the timing chain. 2. Remove the oil pan. 3. Remove the three oil pump screen and cover bolts, then remove the screen and cover. 4. Remove the oil pump screen and cover spacer. 5. Remove the four oil pump mounting bolts, then remove the oil pump from the engine. To install: 6. Clean and inspect the mating surfaces. 7. Install the oil pump and loosely install the four oil pump mounting bolts. Tighten the four oil pump bolts in sequence to 71-106 inch lbs. (8-12 Nm). 8. Install the oil screen and cover spacer to 15-22 ft. lbs. (20-30 Nm). 9. Install the oil screen and cover, then install the three oil pump screen and cover bolts. Tighten the bolts near the oil pick up screen to 15-22 ft. lbs. (20-30 Nm) and the bolts at the opposite end of the pick-up to 70-106 inch lbs. (8-12 Nm). Install the timing chains, then install the oil pan.


Oil pump on a 2000 ford f-150?

Oil Pump Removal & Installation4.6L and 5.4L Engines1. Remove the timing chain. 2. Remove the oil pan. 3. Remove the three oil pump screen and cover bolts, then remove the screen and cover. 4. Remove the oil pump screen and cover spacer. 5. Remove the four oil pump mounting bolts, then remove the oil pump from the engine. To install: 6. Clean and inspect the mating surfaces. 7. Install the oil pump and loosely install the four oil pump mounting bolts. Tighten the four oil pump bolts in sequence to 71-106 inch lbs. (8-12 Nm). 8. Install the oil screen and cover spacer to 15-22 ft. lbs. (20-30 Nm). 9. Install the oil screen and cover, then install the three oil pump screen and cover bolts. Tighten the bolts near the oil pick up screen to 15-22 ft. lbs. (20-30 Nm) and the bolts at the opposite end of the pick-up to 70-106 inch lbs. (8-12 Nm). Install the timing chains, then install the oil pan.


How do you replace the oil pump in your 1995 ford f-150 v8 5.8?

Oil Pump Removal & Installation 4.6L and 5.4L Engines 1. Remove the timing chain. 2. Remove the oil pan. 3. Remove the three oil pump screen and cover bolts, then remove the screen and cover. 4. Remove the oil pump screen and cover spacer. 5. Remove the four oil pump mounting bolts, then remove the oil pump from the engine. To install: 6. Clean and inspect the mating surfaces. 7. Install the oil pump and loosely install the four oil pump mounting bolts. Tighten the four oil pump bolts in sequence to 71-106 inch lbs. (8-12 Nm). 8. Install the oil screen and cover spacer to 15-22 ft. lbs. (20-30 Nm). 9. Install the oil screen and cover, then install the three oil pump screen and cover bolts. Tighten the bolts near the oil pick up screen to 15-22 ft. lbs. (20-30 Nm) and the bolts at the opposite end of the pick-up to 70-106 inch lbs. (8-12 Nm). Install the timing chains, then install the oil pan.


How do you remove the oil pump of a 97 ford expedition?

Oil Pump Removal & Installation 4.6L and 5.4L Engines 1. Remove the timing chain. 2. Remove the oil pan. 3. Remove the three oil pump screen and cover bolts, then remove the screen and cover. 4. Remove the oil pump screen and cover spacer. 5. Remove the four oil pump mounting bolts, then remove the oil pump from the engine. To install: 6. Clean and inspect the mating surfaces. 7. Install the oil pump and loosely install the four oil pump mounting bolts. Tighten the four oil pump bolts in sequence to 71-106 inch lbs. (8-12 Nm). 8. Install the oil screen and cover spacer to 15-22 ft. lbs. (20-30 Nm). 9. Install the oil screen and cover, then install the three oil pump screen and cover bolts. Tighten the bolts near the oil pick up screen to 15-22 ft. lbs. (20-30 Nm) and the bolts at the opposite end of the pick-up to 70-106 inch lbs. (8-12 Nm). Install the timing chains, then install the oil pan.


How do you change an oil pump on a 1999 ford expedition?

Oil Pump Removal & Installation4.6L and 5.4L Engines1. Remove the timing chain. 2. Remove the oil pan. 3. Remove the three oil pump screen and cover bolts, then remove the screen and cover. 4. Remove the oil pump screen and cover spacer. 5. Remove the four oil pump mounting bolts, then remove the oil pump from the engine. To install: 6. Clean and inspect the mating surfaces. 7. Install the oil pump and loosely install the four oil pump mounting bolts. Tighten the four oil pump bolts in sequence to 71-106 inch lbs. (8-12 Nm). 8. Install the oil screen and cover spacer to 15-22 ft. lbs. (20-30 Nm). 9. Install the oil screen and cover, then install the three oil pump screen and cover bolts. Tighten the bolts near the oil pick up screen to 15-22 ft. lbs. (20-30 Nm) and the bolts at the opposite end of the pick-up to 70-106 inch lbs. (8-12 Nm). 10. Install the timing chains, then install the oil pan.


How do you change the oil pump on a 2002 ford expedition with a 4.6l Triton?

Oil Pump Removal & Installation4.6L and 5.4L Engines1. Remove the timing chain. 2. Remove the oil pan. 3. Remove the three oil pump screen and cover bolts, then remove the screen and cover. 4. Remove the oil pump screen and cover spacer. 5. Remove the four oil pump mounting bolts, then remove the oil pump from the engine. To install: 6. Clean and inspect the mating surfaces. 7. Install the oil pump and loosely install the four oil pump mounting bolts. Tighten the four oil pump bolts in sequence to 71-106 inch lbs. (8-12 Nm). 8. Install the oil screen and cover spacer to 15-22 ft. lbs. (20-30 Nm). 9. Install the oil screen and cover, then install the three oil pump screen and cover bolts. Tighten the bolts near the oil pick up screen to 15-22 ft. lbs. (20-30 Nm) and the bolts at the opposite end of the pick-up to 70-106 inch lbs. (8-12 Nm). 10. Install the timing chains, then install the oil pan.


Where is the fusible link to the fuel pumps on a 1985 Ford Bronco?

Well if you have a 351 in the bronco then your fuel pump is mounted on the block right in front of the oil filter


How do you replce the oil pump on a vectra?

Drain the oil from the oil pan. Remove the oil pan by removing the oil pan bolts. Remove the oil pump retaining bolts. Reverse the process to install the new oil pump.


How much oil does a 1988 Ford Bronco II hold?

5 quarts if changing Oil Filter 4 Quarts if NOT changing Oil Filter