0
In recent years, more and more companies pay attention to cut down cost in order to remain competitive. And it's no doubt that workers' efficiency is one of the most important means to save your cost. Are you at a loss? Don't be afraid, there are many ways to go. Strap Lid, which is a brand-new product and an amazing advanced technology as well, can be an integrated solution to meet your needs.
Some modern manufacturer had already developed this kind of product. (e.g. Horen Plastic) Not only easy to operate, but also has an apparent significance to our environment.
If strap lid tech is introduced into your logistics, strap lid will eliminate one-time-use material using. Meanwhile, it will steadily increase your work efficiency which means reduce your manual cost. It is a small cost for one time but it might be big for one whole year. Not to mention the environmental benefits, tidier workplace, branding effect and so on. Want to know where to buy or how to use? You can simply Google "strap lid tech". I'm sure you will find an appropriate answer for you.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do organisations operate in the art and design industry?
Organizations operate smoothly within the art and design industry. They hold shows in art galleries, host fashion shows, and sometimes they hold benefits to raise money for causes.
What is rotary kiln?
A Rotary kiln is a pyroprocessingdevice used to raise materials to a high temperature (calcination) in a continuous process.
What does a crane consist of?
I work for a crane manufacturer, so I know something about it. A crane like 1.0 Mini Crawler Crane is a mechanism that uses a collection of simple machines to both raise and lower objects, and also move them horizontally. They are always equipped with at least a winder; cables, ropes，chains or sheaves.
Steps of synchronizing steam turbine generator?
1. Turn Electronic Governor Switch on. 2. Open casing drain valves 3. Check bearing oil levels 4. Reset Over-speed Trip 5. Put bearing cooling water on 6. Crack exhaust (outlet steam header) and adjust drain valves accordingly 7. When warm crack inlet steam valve allowing turbine to run at 10rpm 8. Check bearing oil rings 9. Look for carbine seal run offs 10. When turbine is warm fully open inlet steam valve and allow governor to take control to 2200rpm 11. Use speed knob to raise speed to 3600rpm 12. Turn Field Excitation Switch on 13. Check incoming and grid voltages and match turbine generator excitation to grids voltage using the field excitation rheostat. 14. Use speed knob to reach 60hz 15. Turn on synchronization switch to the synchroscope 16. Adjust turbine speed to adjust the phase angle/frequency to a steady slow clockwise rotation on the synchroscope. 17. Close generator breaker at the 5min to 12'oclock position on the synchroscope. 18.Turn of the synchronization switch to the synchroscope. The turbine is now synchronized to the 60Hz power grid.
What is a textile slitter operator?
a slitter operator runs a machine that slits fabrics. A roll usually 70 in in length of fabric and maybe around 300-1200 yards is loaded onto the back of the machine. Fabric is tied off and ran through the machine around rollers, under platform, through knife setup, around and through pinch rollers in the front. Machine is set to a particular cut size with the amount of rolls, length, and heat expansion factored in. Machine is then set to a low speed to roll as it heats up. Machine is heated between 680 and 720 degrees depending on process control. If the machine heats up without being in motion, the heat bar will warp. Once machine is up to temp, now we set the beds. Beds are lined up with knives. If beds are set before machine heats up to temp, they will all have to be reset due to heat expansion. Once beds are set, we will clean all carbon off of our knives. Now, we set all controls to what developed process calls for. Usually with peel ply Ill set my top and bottom clutch (front rollers) to 20. ill set my brake at around 30+ depending on weight of roll, amount of yards, and roll's core fit (loose or tight) on brake arm. Brake should be decreased throughout. too much brake and it will pull causing stress on clutches. Not enough brake and the clutches will pull the roll too fast and you will end up with a burnout/floppy selvage/creases/shifts/telescoping. Now we will make a test cut with all the beds set, machine heated, low brake... before we do the test cut, we load up the correct amount of cuts worth of cores staggered between top and bottom clutch with two extra for the selvage (unless you have an air suction system which is great until you lose air and then you have a major burnout and loose reels, have to drop beds, or doff early... Now that he clutches are set with cores. an experienced operator would usually already have cheat marks on the air shaft for core line up. But since we are inexperienced, lets waste some fabrics and make some cuts to line up our cores... Set brake to around 15-20... raise pinch roller...set edge eye..run fabric through machine enough for edge eye to straighten roll. YPM should be set to above 25 as to not carbon up your knives.. raise the bed bar to the knives and run the cuts up through to the front. Stop First! drop bed bar. Run to front of machine...tape across the cuts to keep them together and perfectly lined up... now adjust your cores to line up with your cuts and selvage. Once you have a line up..Shoot some air in the shafts... throw some two sided tape across both top and bottom clutches over cores all the way across in one swipe for each clutch... wrap cuts over the two sided tape and press.... cut away the waste, make your cheat marks on the left hand side of each core on the shaft with a dry erase marker. NOW raise those beds and start it up.... HELPFUL INFO: spatulas, scissors, screw drivers, collar tighteners, and heat resistant gloves are your best friends...... this walkthrough is only for a performance 3in dual shaft slitter.... Cutdown, Inkers, and wide impression slitters are different but run on the same basic ideas. You may have knives of different sizes which of course would have to be calculated by your Setup technician. Some have 1 1/4 in shafts.... Cutdown slitters usually have smaller knives .125 and slit smaller rolls that were preslit on a wide roll slitter. Wide slitters have larger knives.. usually .250 per knife to calculate you setup, you need to calculate heat expansion... On your basic 70 in setup on 2 1/2 in calrod. if you are setting up for 3in cuts....depending on the variance you are allowed, to get closest to 3in we will use.... A. .250 knife B. combination of spacers C. .250 knife heat expansion would be 3.000 times 1.006 minus 3.000 which should equal .018 which needs to be calculated into your spacer setup depending on what variance you are allowed to have..... I was setting up and operating with a 1/32 of an in max and 1/64 of an inch target... spent many days looking through an optical comparator during process creation..... good luck... find another job
If the supply of workers and demand for workers is at an equilbrium what would be true?
there is no pressure to raise or lower wages.
What is the participail phrase in Requesting a raise in pay the workers started complaining about their jobs?
requesting a raise in pay
How does the government protect the steel industry?
raise taxes
What are state level party workers?
They help raise compaign money
What do state level party workers do?
they helps raise compiag money
What are the duties of state level party workers?
They help raise campaign money.
What is the duty of state level party workers?
They help raise campaign money: NOVA NETThey raise campaign money(Nova Net)
On the online game Ikariam how do you raise your income fast?
cut down on researchers and workers
What industry do you work in if you grew crops and raise animals?
I have know I dea so you do it!
What is United Farm Workers?
the united farm workers is an organization started who's main goal was to give farmworkers better working conditions and a raise in their salaries
What types of livestock do ranchers raise?
Ranchers raise a wide variety of livestock depending on their ranch. A rancher would mostly raise cattle for beef as selling beef is profitable in the fast food industry.
How many Kwh to raise 1 l water 1 degree c?
0.001167 kWh/°C/l at 100% efficiency.
