answersLogoWhite

0


Best Answer

The grove on the front of the pulley requires a sleeve in a u shape that slides over the pulley grove and a fine threaded bolt is part of the the sleeve assembly than you tighten the bolt which in turn pushes on the pump shaft removing the pulley. They are avaible at NAPA Stores

User Avatar

Wiki User

โˆ™ 2008-04-23 18:47:24
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How to remove PS pump pulley from 1999 73 diesel?
Write your answer...
Submit
Related questions

How do you remove power steering pump pulley on 1999 lesabre?

Pulley is pressed onto pump, you need a puller to remove.


How do you change your power steering pump on a 1999 mazda b2500?

You need a special tool, pulley puller and installer to remove the pulley first then you remove both hose and bolts to remove the pump, then install new pump and hoses, bolts and finally install the pulley with the special tool, never try to hammer in the pulley, if you do new pump will brake


How do you change 98 a4 diesel pump?

Remove the belt from your diesel pump. Remove the diesel pump fuel lines. Remove the diesel pump retaining bolts. Reverse the process to install your new diesel pump.


How do you remove the steering pump pulley on a Nissan 200sx?

Take off the sockets and remove the pump pulley.


97 Ford F-350 diesel with a 7.3 power stroke how do you remove the power steering pump pulley?

n way around it you have to pull the radiator to get the puller on the pulley


How do you remove Allen screw from power steering pulley?

That is not a Allen screw in there. That is part of the pump shaft. If you are looking to remove the pump pulley you will need a power steering pulley puller. This tool will help you remove it and replace it, without the puller you will damage the pulley or the pump or both.


Hw do you remove power sterring pump pulley on a 91 Cadillac Seville?

Begin by removing the power steering pump belt from your 1991 Cadillac power steering pump pulley. Remove the power steering pump pulley retaining bolt. The retaining bolt will be in the center of the pulley.


How do you remove pulley from power steering pump 95 Chevy silverado?

This requires a power steering pulley puller. This puller is designed to remove and install a power steering pulley without damage to the pulley and or pump. Attempting to do this without the puller will result in damaging the pulley or the pump or both.


Removing pully from power steering pump do you need to remove the pump or is there a trick to it?

To get the pulley off requires a pulley puller to do it. You do not have to remove the PS pump to do it. It also takes a special tool to put the pulley back on too.


How do you remove power steering pump in 1995 Toyota 4runner?

To remove the power steering pump, you will have to disconnect the air control valve hoses( two of them buttom of pump) then the retun hose. then the high presure hose. the pulley well have to be removed before you can remove the pump. the way to remove the pulley is by removing a nut that holds the pulley in place. then to frace the pulley off the pump use a ball joint separater tool between the pump and the pulley and hammer it until the pulley slides off. then unblot it form the bracket.


How do you remove a wrx power steering pump?

Undo the hoses remove drive belts from pulleys undo pulley bolt and remove pulley no special tool needed should slide off remove bolts at front of pump remove pump


How do you remove and replace a water pump on a 1999 ford contour?

Drain antifreeze. Jack Passenger side of car up. remove wheel well skirt. loosen pulley bolts on water pump before removing serpentine belt. loosen a/c compressor and slide forward about an inch. remove pulley from water pump. remove 4 bolts holding water pump in. remove water pump. reverse sequence to put new in.


How do you remove fan from water pump on 96 dodge 3500 1 ton?

36mm wrench and a holder for the pulley. The fan is reverse threaded on a diesel.


You need to remove the power steering pump Do you remove pulleypumpbracket first then try and get pulley off repair manual says remove pulley first but removal tool too long to fit.?

There is a bolt that is blocked by the pulley. In order to remove the pump you need to remove that bolt. So you need to remove the pulley first to get access to that bolt.


Where is oil pump on 7.3 ford diesel?

Simple enough. pull the harmonice balancer, aka the crank pulley. remove the crank seal and there is the low pressure motor oil pump for the 7.3


How do you take the power steering pump off a 1999 Pontiac grand am?

First remove the serp belt, then you will have to remove the pulley from the pump, if the pulley has no holes, other wise use a 13m socket with a 3in extension, & remove the 3 retaining bolts & loosen the lines & remove. . Pretty easy. . good luck. .


How do you replace the power steering pump on a 2001 gmc Yukon?

Remove the belt from the pump. Disconnect the lines and drain the fluid into a container. Unbolt and remove the pump. Using a puller, remove the pulley from the power steering pump. Mount the pulley to the new pump. Reverse procedure to install.


How do you remove the water pump pulley on a 1985 Oldsmobile cutlass ciera?

pulley puller


How do you remove the pulley on a 1991 Suburban 5.7 power steering pump?

POWERSTEERING PUMP PULLEY PULLER (ADVANCE AUTO RENTS THEM)


Where is the water pump 06 montycarlo?

Behind the water pump pulley. The water pump is small so the water pump pulley covers the entire pump so you can't see it. Once you remove the serpentine belt and the water pump pulley, the pump is easily accessible.


What is the tool needed to remove the power steering pump pulley on a 1999 1500 Suburban 5.7?

you can rent one at a auto parts store


How do you remove power steer in pump on factory no air Chevy?

You have to remove the pulley first and you need a power steering pulley puller to do it. You can get one from Napa for usually about $40. There are bolts behind the pulley that hold the pump to the mounting bracket.


How do you replace the water pump on a 1994 Nissan Sentra?

Not sure on a '94, but on a '90 w/ a 1.6 you just remove the pulley bolts on the water pump, take off the pulley and belt, remove the thermostat housing on the side of the water pump, and then remove the water pump bolts. After that you can take off the water pump.


How do you remove the pulley on the steering pum p on a 2001 sierra?

You need to rent, borrow or purchase a power steering pulley puller. This tool will remove and replace the pulley without damage to the pulley or the pump.


How do you remove a water pump on a 1994 Chevrolet camaro?

Drain coolant Remove 4 bolts that secure fan and pulley on water pump Remove Belts Slide fan and pulley off water pump shaft Loosen and remove bolts securing water pump Remove coolant hoses if required Remove water pump Clean engine surface before installing new pump and gasket ya what he said......lol

Study guides

๐Ÿ““
Create a Study Guide