answersLogoWhite
Mitsubishi Montero, Pajero, and Shogun
Nissan Quest
Mitsubishi Trucks
How To

How to replace electric antenna rod in 97 Quest?

505152

Top Answer
User Avatar
Wiki User
2006-07-27 23:00:54
2006-07-27 23:00:54

with the ignition on have some one turn the radio on and when the antenna starts comming up grab it and continue pulling and it will came all of the way out. to insatll the new one, just feed the end down the hole until it stops and theb=n have someone to turn radio off and it will lock in and continue just guide it all of the way.

1

Related Questions

User Avatar

You simply unscrew the antenna rod and replace it. Very easy.

User Avatar

remove inner fender passenger side remove antenna assembly go buy one at local parts store about 56 dollars

User Avatar

Grounding is accomplished by connecting a heavy cable from the ground side of the antenna to a ground rod. A ground rod is typically a 4 - 8 foot copper plated steel rod driven into the ground as close as possible to the antenna, making the wire connection as short as possible. All equipment should also be grounded to a rod, not just the antenna.

User Avatar

The antenna becomes a lightning rod. By connecting the post it is attached to, to the ground via the metal rod driven into the ground, lightning will not pass along the antenna wire to your TV but will pass harmlessly through the post only.

User Avatar

You get the Rod of Irvandis during the In Aid of the Myreque quest, it is used at the almost end part to finish the quest, and yes you do keep it when quest is complete.

User Avatar

A Dragon Rod costs 39800 gold, and can be bought from the Stornway weapon shop, after you finish the main quest.

User Avatar

If you lose a quest item like the taming rod, then all you need to do is abandon the quest and re-take it. You will receive a new one when you re-accept the quest.

User Avatar

Mostly because an antenna is usually the tallest part of a house, and made of metal, which attracts lightning. if lightning hits the antenna it will follow use the metal rod to reach the ground instead of going through the house. Also partly because an antenna works better if it's grounded.

User Avatar

> http://www.myfordfocus.com/how-to/antenna.htm < OR; If you're just looking to replace the antenna rod itself - It is just screwed into the base. I have a 02 wagon, and have taken it off a couple of times. You might have to tighten it a bit first to break the seal. then grap it good an unscrew it. It seems to stick, but comes off. Good luck

User Avatar

I just did this today. It took about 2hours. Take your front tire off and loosen about 5-9 bolts that hold the innter fender panel on. Then you can pull back and disconnect 2-3 bolts that hold the antenna in. My problem now is that I can't get the new rod to retrieve back into the antenna. Hope this helps. Mike

User Avatar

Lighting rod is metallic rod, the rod provides easy route for the transfer of electric charge to the ground.

User Avatar

When you find a new rod to replace the broken one, simply click on the broken one and the new one will replace it. (To get the fuel rod , see the related question.)

User Avatar

There will be some amount of continuity in a k30. There is a coil at the bottom of the antenna base, so the ohm reading will be high, but should still be there.

User Avatar

The average cost to replace a tie rod is approximately $200. You can save about $125 of labor by replacing the tie rod your self.

User Avatar

how much will it cost to replace or repair rod for 1996 volvo 960?

User Avatar

A rod made out of ebonite, a hard rubber. The ebonite rod is often used in physics demonstrations of static electric charges.

User Avatar

lightning rods help you because of the metal in the rod

User Avatar

buy a replacement antenna. undo the nut on the wing that secures the antenna. now turn the stereo on. the antenna will rise. when it gets to the top position it will pull out with no problem. leave the stereo on at this point. insert the white plastic track of the new antenna until you feel it almost grip. now turn the stereo off. the motor will now pull in the white plastic strip. now do the nut up again and job is complete. for any further assistance please visit. www.pajerouk.co.UK

User Avatar

Replace the engine.Replace the engine.

User Avatar

The rod bearings are between the connecting rod and the crankshaft.

User Avatar

Yes, replace tie rod and have the car realigned.

User Avatar

Remove the old tie-rod from the knuckle. Loosen (or preferably replace) adjusting sleeve. Put on new tie rod and tighten everything down. Then take it and get it aligned.

User Avatar

You can not tighten a T-Rod end up. If it is loose then replace it.

User Avatar

The estimated cost to replace one inner tie rod end on a 2003 Isuzu Rodeo is between $121 and $227 including parts and labor. The estimated cost to replace one outer tie rod end is $118 to $205.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.