Lamp sockets are located inside trunk. There will be a little door/cover along the outerwall of trunk lining on either side. Pop the little door/cover off & you will see 3 sockets inside. Twist the socket to unlock it, change bulb, then replace socket and twist it to lock it into position.
You have to unbolt the entire tail lamp assembly to change the bulbs. Unbolt the tail lamps from inside the corners of the bed, replace the light bulbs, bolt the tail lamps back in place.
rear tail light fuse
If you mean "Lamps"; In your "Owner's Manual", for Front see page 6-36: Headlamps, Front Parking and Turn Signal Lamps. For Rear see page 6-38: Tail/Stop/Turn Signal and Rear Sidemarker Lamps, under Section 6: Service and Appearance Care - Bulb Replacement...
The tail lamps are serviced from underneath the vehicle, between the frame extension and rear bumper.
In order to replace the rear window tail light you need to get into the truck. Once inside the trunk look to the top of the trunk and look at where the screws are for the rear tail light. Unscrew them and the entire housing for the light will pop off.
where are the bolts?
lift the tail gate and there are two phillip head screws on the metal by the tail light.
replace rear tail light bulb
See Tail Lamps, Turn Signal, Stop Lamps and Sidemarker Lamps on page 5-57 of your "Owner's Manual", under Section 5: Service and Appearance Care - Bulb Replacement...
I don't think you can replace just cover. Usually you have to get a new tail light.
Bulb is blown. Replace bulb.
I have a similar problem. How do I get to replace the side/brake/fog bulbs in the fitting in the rear lower skirt? Can't see how to get at the lamps at all! Appreciate an email to firstname.lastname@example.org. Thanks
THERE IS NO PARKING LIGHT LENSE FOR THE REAR. IT'S ONLY THE TAIL LAMP ASSEMBLY!
open the lift-gate and take off the tail lamp
I pulled the inside plastic cover of the rear door. Once it is loose at the bottom or lower edge you can reach up and replace the lamps. Then snap the plastic cover back in place.
The rear tail light assembly had problems with the sockets and circuit board. My guess is you will need to replace the socket and circuit board assembly for the passenger side rear tail light.
To replace the rear brake lights on a Nissan Primera first open the trunk lid. Locate the tail lights and find the plastic cover which hide the bulbs. Remove the cover and then the bulb. Replace with a new bulb.
you don't replace the tail light you just replace the bulb in it
To replace the taillight bulbs open rear door, remove the two Phillips screws, pull the whole lamp assembly to the rear, unplug the wiring from the lamp assembly. Now remove the four small Phillips screws on the back. The socket will just pull off and you can get to the bulbs. GM had a recall on the socket assembly because of tail lamps not working. Before reassembling the unit you can just plug the socket in to check if all lmps are working, If not and the lamps appear good bend outward the small wire loops on the lamp to make a better connection
If you lift you rear hatch there are 2 torx screws (I think that they are t30 or t35 ) Just remove them. You must then pull the lens strait out there are two pins holding it on. 2nd opinion: So we are talking about the REAR tail light assembly, as opposed to the FRONT tail light assembly, right? Have you ever seen a "cow" with it's tail in the front?
check your fuse box under the dash. on the cover, or on a nearby sticker, it will indicate which fuses do what. replace whatever fuse says REAR lights, TAIL, ETC.
Technically yes.But you need to check the practicality of it.
Hey Mike== You have to remove the light assy and take them out from the rear. GoodluckJoe
Tail lights are replaced by removing the entire rear plasic cover to the back hatch.
Replace the whole light assembly Their are no bulbs it is neon light