0
Is the load prong on a toggle switch the constant power source?
Wiki User
∙ 11y ago
No the power comes from something other than the switch.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Is a transformer one source of constant electric current?
A; Terminology is not correct a transformer is not really a source but rather a device to transform one source of power to some power that can be used as required minus efficiency of power transfer
Why are dams built as part of large hydro power plants?
To gain a constant source of water.
Why you use constant current source?
What follows below is not a full description. Full descriptions are in chapters of books about electronic power supplies.A constant current source is an electronic device which acts as a source of power whereby, however the load resistance changes - within a certain fixed range - the device is designed to monitor the output current drawn from it and will change its output voltage to keep the output current constant within a certain fixed range.Another answerA constant current source will provide constant current with a load if the load changes the volts will change to compensate for the constant current flowing. Which is just opposite to a constant voltage source whereby a load change will change the current but not the voltage. And that how it works.
What are the componets that make up a circuit?
A circuit can have as little as two components 1 Must have a power source 2. Something for that power source to power, for example a light *Assuming you already know you need wires to complete the circuit
What happens to the coil of wire when someone presses the switch?
If the coil is connected to a circuit and the switch is closed then, provided there is a power source, the coil will become energized.
What is a synonym for toggle?
Synonyms for toggle: adjuster, dial, knob, on/off, power switch, switch, tuner, push button
How do you correctly install a amp toggle switch in 1995 VW Jetta?
the same way you'd install any toggle switch. run your lines from the battery and the ignition to the power and remote switches on the amp. if you follow the directions on the box and the amp doesn't shut off because you've inadvertantly hooked the remote switch to the clock power or some constant source, then take whatever switch you have and simply add it inline between the battery and the amp. blaow. have a gin and tonic and sit in the car and wwitch your amp off and on. it'll be awesome.
How can you rewire a washer fluid motor to just a toggle switch on an 88' Chevy Beretta?
Yes! Find the wires going to the washer switch and just use a toggle switch in it's place. If you can't locate the wires, you can just run power straight to the motor from the toggle switch. I recommend you use a spring loaded on/off toggle switch, to make sure you don't accidentally leave it in the on position.
What is the difference between toggle switch and a push button?
A toggle switch is like a light switch. You flick (or 'toggle') the switch on or off and it stays in that position until you flick it again. You could compare a push button switch to a key on a keyboard. When you press a key momentarily it will display one letter on the screen. If you hold down the key, the same letter will repeat (e.g. aaaaaaaaaaaaaaa). Toggle switches can also look like push button switches. Most power buttons on a desktop computer tower is a toggle switch. The reset button on a computer tower is a push button switch.
How can you get constant power to a receptacle after a light switch?
You'd need to branch the circuit before the switch. This can be immediately before the switch, in the box that holds the switch, but you can't get constant power from a switched circuit after its been switched.
How do you wire ignition to toggle switch?
my ignition is broke and on the on position how can i bypass the ignition n use a toggle for power and a pushbutton to start run thik power wire from positive of battery to starter. then wire from starter to distributer. then run wire inside or vehicle to push start and ground it or run back out to battery to neg. put toggle switch some where in the process to kill it.
How do you install a key start on a ssr 125cc pit bike?
All key systmes are electirical switches. Just like a toggle switch except for with a key for security. Get a switch at a parts store and wire it in between the power source and the ignition. If magneto then wire it to ground the mag.
How do you run three switches and a hot outlet from one incoming power source?
You need to run a wire from the existing power source to switch to switch to switch to outlet.
What does a kill switch look like?
A kill switch is usually nothing more than a common toggle switch. It is usually installed in a hidden place and is used to disrupt electrical power to the starter motor.
How do you use a 14-3 wire for Switch and Power?
you need 2 , 3 way switches on the switch you will have 3 poles 1 will be copper 2 will be silver your 1 copper is power or switch your 2 silver are travelers to toggle the power back and forth , you use the black and red wires for the travelers and use the white for the power on one switch and the white to the other to the light with your neutral ---- power---* *--------* *---switch powered *--------*
How to use toggle switch to turn fans on in a Cadillac?
It's pretty simple to wire toggle switches to fan motors. Bring a power lead from the fuse block (on a protected circuit or install an inline fuse) to the toggle switch. Then take the outfeed line straight to the fan motor. The problem is the fan will only run on HIGH. You can install a rheostat switch the same way and it will give you variable speed control to the fan motor.
Does each switch have its own power source?
Not all switch have there own power source, some of the switches are connected with two or more power sources so it is best to have additional switches to avoid a blowout.
