answersLogoWhite

0


Best Answer

If this is a rubber hose it's your water pump bypass hose.

it is called a bypass tube and to replace it you have to pull the belt tensioner. this is awnsered near the end of Buick regal questions.

User Avatar

Wiki User

15y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Little elbow piece coming off the engine block above the water pump going into looks like the ALT bracer?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Where is the low pressure AC switch on a 1996 Cadillac SLS?

low pressure sensor is located on larger line coming out from fire wall above right side tire and to the rear a little. should be facing towards engine.


Where is starter relay on 1973 mustang?

Little box just above the battery area on the engin bay wall with wires coming out of it.


Where is the coolant temperature switch on 1998 Oldsmobile bravada?

My 1997 is located on the drivers side engine block towards the back above spark plugs it threads into engine and has 2 wires coming out


Where is the water leak coming from above the Center flywheel behind a plastic cover on a side engine 1991 Mazda 626Lx coming from?

It's probably leaking from a faulty water pump. Replace the pump.


Where is the oil filter on a 1999 dodge neon?

back side of the engine, just a little above thebottom of the oil pan


1994 Mark VIII you have antifreeze leaking from the rear of the engine you are not able to see where it is coming from it is not from trans cooling lines appears coming from above no water in oil?

there is a tube that runs from the back of the heads across each other


Does the engine need to be lifted to replace the oil pan on a 1998 Plymouth Voyager?

Yes. You need to unbolt the exhaust pipe from rear manifold and support engine and transaxle from above with engine hoist. Unbolt engine mounts and raise engine/transaxle to make clearance to remove oil pan. This is for V6 3.0 L engine. Yes. You need to unbolt the exhaust pipe from rear manifold and support engine and transaxle from above with engine hoist. Unbolt engine mounts and raise engine/transaxle to make clearance to remove oil pan. This is for V6 3.0 L engine. A little bit different for 4 cylinder. Yes. You need to unbolt the exhaust pipe from rear manifold and support engine and transaxle from above with engine hoist. Unbolt engine mounts and raise engine/transaxle to make clearance to remove oil pan. This is for V6 3.0 L engine. A little bit different for 4 cylinder. Yes. You need to unbolt the exhaust pipe from rear manifold and support engine and transaxle from above with engine hoist. Unbolt engine mounts and raise engine/transaxle to make clearance to remove oil pan. This is for V6 3.0 L engine. A little bit different for 4 cylinder. Yes. You need to unbolt the exhaust pipe from rear manifold and support engine and transaxle from above with engine hoist. Unbolt engine mounts and raise engine/transaxle to make clearance to remove oil pan. This is for V6 3.0 L engine. A little bit different for 4 cylinder.


How do you illustrate that an area is below sea level?

You'd draw the land first. Then draw the ocean coming up right a little above the edge of the land.


Where is the oil pressure sender on a Plymouth Breeze?

Mine is on the back of the engine block.. right above the drive axle , there is one there called crankshaft sensor and then right above it is the oil pressure sensor mine has one wire coming out of it...


Where are location the switch temperature?

Howdy, if you are looking for the engine temp switch(sending unit, it is located on the engine next to the large coolant hose (the hose that is not attached to the pump) on the engine. Just a little above and to the passenger side of the vehicle.


Where is the oil switch located on a 07 chrysler Aspen 4.7 engine?

It is located on the front of the engine, above the oil filter.It is located on the front of the engine, above the oil filter.


Where is the Cam sensor location on a Ford F150 Ford 4.2 V6 Engine?

look above the water pump on the timing cover its a black round senser with wires coming off it