Locations of engine mounts on 94 Nissan altima?
1 under air filter, 1 beside p/s tank, 2 on cross member underneath only 2.4 liter
Loosen all of the motor mount retaining bolts. Jack one side of the 2000 Nissan engine up. Remove the retaining bolt. Remove the motor mount bushing and replace it with a new one. Do the same thing for all for motor mounts. Let the engine back into its original position and tighten the retaining bolts.
My Altima shift really hard from 1 to 2 i replace motor mounts O sensors add slick 50 to transmission and is the same Can you advise something to make shift softly beside drive really slow from 0 to 2?
What year Altima? If 2003-2005 and the 'Service Engine Soon' light is on, it could be this problem: http://www.justanswer.com/uploads/baddad1/2009-02-20_190936_NTB05-001.pdf Service Bulletin: NTB05-001 2003-2005 NISSAN ALTIMA, SENTRA, 2003-2004 MAXIMA, 2004 QUEST; 4 SPEED AUTOMATIC TRANSMISSION HARSH 1-2 SHIFT AND/OR DTC P0745 STORED
Can you put a 3.5L Nissan maxima engine in a 2003 Nissan sentra without having to spend a ton of money to change everything?
Lift and properly support front of car. Remove the nuts from lower half of the mounts (one per mount). Raise engine enough for the mounts to clear the frame brackets and support engine safely. Unbolt motor mount brackets from engine block. Remove mounts with engine bracket. Unbolt motor mounts from engine brackets on the bench. Reverse procedure for installation.
Is it necessary to loosen the engine mounts when changing an oil pan gasket on a 1996 Nissan 200SX 1.6L engine?
you could butyou will have to use the Nissan transmission and transfercase you will also have to make motor mounts a crossmember and fabricate both driveshafts . then youll need to incorporate the computer from the Nissan to get it to run . i wouldn't attempt this unless you have a lot of experance and a lot of free time .its easier to just find a good engine like you need at the junk yard…
Where are the motor mounts and transmission mounts on a 1997 Ford Taurus gl And how can i tell if they are worn out or bad?
Yes...you can put just about any engine in anything with the proper skills, time and money. If the Cutlass you have has an Olds engine in it now then the transmission will bolt right up to the Pontiac engine. If it's a Chevy engine you'll need a B.O.P. transmission. You will need to change the motor mount location. Depending on the year of the Cutlass it may actually have the bolt holes drilled in the…
Assuming you mean engine mounts, these days broken engine mounts will still hold the engine in place not like the older mounts from the 60's and older that allowed the engine to flop around when they broke like a fish out of water. The engine cooling fan may rub the radiator shroud under acceleration and you may also hear some clunking and feel some vibrations. Replacing the mounts would be recommended.
2, a left and a right. No, an Acura 2.5 TL has four engine mounts. A left and a right hydraulic mount located in the engine compartment, at the middle of the engine and two more mounts under the car bolted to the front of the transmission. The last two should really be called transmission mounts but they are listed and sold as motor mounts. The two front mounts cost at least $350.00 EACH!! The…
MOTOR MOUNTS Motor mounts should always be replaced in pairs or sets along with transmission mounts. Age, oil and grease cause deterioration of the rubber leading to vibration, chatter and failure. No restoration is complete without new motor mounts. Motor mounts (engine mounts) are used to connect a car engine to the car frame. They are usually made of rubber and metal. The metal portion connects to the engine on one side and to the…