answersLogoWhite

0


Best Answer

the interior door panel is tricky to get off. first remove the two screws in the finger well and one screw in the control panel, behind the door release, and one more on the driver mirror panel. using a large flat blade screw driver, place it on the edge of the plastic panel containing the door lock and pull latch. gently hit the handle of the screw driver to push the pannel toward the front of the car, it should slide about 1/4 of an inch. next, with the same screw driver, begin by prying the door panel away from the door frame starting from the bottom and working your way up around the sides. the panel is held in by white ribbed plastic clips, there are two of them hidden just above the control pannel you just slid to the right. slowly work them out as to not rip the door panel. once they are all free, grab the upper left corner and the lower right corner with both hands. pull out toward you gently to keep the clips from resetting into the door body, twist the door panel in a clockwise rotation, the lower left side of the control panel should slide down into the door panel as you twist, sometimes it needs some help. once you start twisting the panel it should be apparent on how to bring the rest of the control panel through the opening. the installation is just the reverse.

User Avatar

Wiki User

16y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Need help in removing a door panel from a 1996 Saturn SL1?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What repairs transmission on 1996 Saturn?

need way more information


Can you replace a 96 Saturn engine with a 92 Saturn engine?

YES BUT. YOU SHOULD USE THE 1996 CRANKSHAFT AND THE 1996 INTAKE SO YOU NEED TO DISASEMBLE BOTH ENGINE TO DO ONE


How do you remove a 1991 Chevy Silverado door panel?

Removing a 1991 Chevrolet Silverado door panel is pretty simple. All you will need to do is to remove the screws holding the door panel in place.


Remove door panel off 1996 Chevy Silverado truckvl?

What do I need to do to take the door panel off a 1996 Chevy Silverado? Pickup has power windows and door locks I need to fix inside door handle


Does a 1996 Ford Thunderbird have a fuel pump access panel?

No. The 1996 Ford Thunderbird does not have a fuel pump access panel. You would need to get the car on a lift and then drop the gas tank. Then you can reach the fuel pump.


How do you remove the door panel from a 95 ford escort wagon?

Removing a door panel from a 1995 Ford Escort wagon is very simple to do. The clips that are holding the door panel in place need to be removed, then the screws in the door will need to be taken off. After the clips and screws are removed, the door panel can be lifted off.


You have taken apart a motor for a 1996 SL Saturn The oil was leaking into the antifreeze Does this sound like you need a new head?

The 1996 Saturn more likely has a blown head gasket. The gaskets will give this problem. If the head is in doubt it can be checked for warpage.


What is the term for removing programs you no longer need?

It is called "uninstall". This can be done from the control panel, then add/remove programs. Good luck!


Need to locate the fuse box and the relay switch for the power windows on a 97 Saturn SC1?

Located in the passenger side kick panel


Replace timing belt Saturn 1996?

Not Applicable The Saturn 4 cylinder, both the SOHC and DOHC used a chain, and it doesn't need to be replaced unless the engine has OTHER problems.


How do you remove the rear speakers in a 2003 Mitsubishi eclipse?

You need to remove the rear seat and the panel covering the speaker. Before removing the panel make sure that you have removed all screws. Pay attention to the clips holding the panel as well.


How do you replace the front speakers in a Saturn 2001 L200?

You will need a Phillips head screw driver and a universal window crank removing tool. unscrew the scres at the bottom of the door panel. and pop of the tweeter grill there is a screw there and one behind a plastic piece where the window switch would be. take off the door panel. and the rest is just to remove the speaker. get a nice carbide drill bid for you will need to make new speaker mounting hole in the door.