answersLogoWhite

0


Best Answer
Copy

side of the block, against the firewall, passenger side side of the block, against the firewall, passenger side

User Avatar

Wiki User

โˆ™ 2008-02-28 01:59:40
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: Need to know location of crank sensor for 2.8 v6 buick regal?
Write your answer...
Submit

Related Questions

Where is the crankshaft sensor on your 99 buick regal?

Behind the crank pulley


Why does my 1993 Buick regal crank but doesn't start?

could be the crank sensor, the go out. the have a reputation for that.


Why does your 1988 Buick Regal not start when you try to crank it after it has been running?

if it has a crankshaft sensor that's bad


Where is the knock sensor on a 1992 Buick Regal 3800?

Where is the knock sensor located on a 1992 buick regal


MAP sensor on 2001 Buick Regal LS?

Where is the map sensor on a 2001 Buick Regal Ls


Where is the headlight sensor for a 1999 Buick regal?

Where is the headlight sensor for a 1999 buick regal? Its in the back, sike ;D


Where is the location of the cam sensor in a 1988 Buick Regal with 2.8 engine?

The 2.8 engine doesn't use a cam sensor.


Would a bad crank sensor produce a check engine light code for a 1999 Buick Regal LS?

Yes


Location for temperature switch for 1996 Buick Regal?

where is temperature switch on 1996 buick regal


What does the camshaft position sensor on a 1992 Buick Regal look like?

The camshaft position sensor on a 1992 Buick Regal looks like the end of a ratchet.


Where is the coolant temperature sensor located on a 1992 Buick Regal with a 3.1 engine?

On a 1993 buick regal it is on the side of the radiator.


Where is the low level coolant sensor on a 2000 Buick Regal 38 not supercharged engine?

Coolant Recovery Reservoir. There is no sensor in the coolant recovery tank on a 1998 Buick Regal.


Where is the coolant temp sensor for a 1992 Buick regal with a 3.1 engine?

On a 1993 buick regal it is on the passager side of the radiator. Hope this helps


Where is the crankshaft position sensor located on a 92 Buick Regal 3.1 V6?

The crankshaft position sensor, on your 1992 Buick regal 3.1 liter, is located on the back of the engine. The crankshaft position sensor is on the inside of the engine cover.


How do you remove a Crankshaft Position Sensor?

how to remove crankshaft position sensor from 91 Buick Regal


Where is cam sensor on 99 Buick Regal?

The cam sensor on a 99 Buick Regal is located behind the rear cam bearing cap. It monitors the rotation of the cam and relays information to the vehicle's computer.


Where is the PCV valve on a 1993 Buick Regal 3.1L?

On a 1993 Buick Regal 3.1L, the PCV valve is located on the intake manifold. It is situated underneath the MAP sensor.


When was Buick Regal created?

Buick Regal was created in 1973.


Where is the crankshaft sensor on 2000 Buick Regal 3800 V6 and how do you change it?

The sensor is located in between the crank pulley and front cover, just to the lft of the crankshaft. In order to change the sensor, you must, first, remove the crank pulley. With the damper off, unplug the sensor, and pull off the plastic cover. The sensor is mounted with 2 bolts, just to the left of the crankshaft. You'll need a deep 15mm socket.


Why would a 1996 buick regal stall after heat stop working?

Make sure you have engine coolant. If the engine isn't getting enough coolant, it will overheat, stall and possibly destroy the engine. One symptom is that no coolant is circulated into the heater. Also check the crank sensor, but check coolant first...then the crank sensor.


What if the electronic speedometer on your 1992 buick regal does not work what could be the problem?

Vehicle Speed Sensor


Temperature gauge not reading properly on 94 Buick Regal?

Most likely a bad sensor


Is the shift sensor solenoid located inside or outside of the transmission on a98 Buick regal gs?

No


How do you replace cam sensor on buick regal 3.8L?

In order to replace the cam sensor on a Buick Regal 3.8L, you must first access the main dash board from the back by either entering the hood or removing the panel, and then crossing the two wires in question.


Where is crankshaft position sensor located on a 1994 Buick Regal 3.8 and how do you replace it?

behind the crank shaft pulley. remove pulley and install new one make sure to replace it in the exact same spot it was before of you will tear up your new sensor