0
The clutch is probably too used
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Why wont my 1987 5speed legend wont go in gear when car is on?
My first suspect would be the clutch. Have a competent mechanic take a look at it.
Back end of car - car wont drive but will go in reverse?
If you have an automatic transmission, it probably has a forward clutch/band problem.
Why wont my 68 VW Beetle go into gears while the car is on?
The clutch is shot or in need of an adjustment.
When you shift gears and press on the gas again the car wont go then it will shake violently then accel erate?
you have to ease on the clutch, transition between releasing the clutch and applying the gas.
My 68 volkswagon bug will go into first gear when its off but wont when the car is on anyone know why this is?
Your clutch isn't releasing entirely.
What is wrong when the clutch won't go into gear?
A clutch does not go into gear. A clutch engages, Normally if a clutch fails to engage it is because it is worn. with a worn out clutch you are able to start the car in gear without your foot on the clutch and the car wont move. Normally before this happens you will notice what is known as a slipping clutch. A slipping clutch means that the engine is turning faster than it should to keep the car moving while in gear. once this starts to happen it does not take long for the whole show to come to a stand still.
Why won't your manual transmission car go in reverse and other gears?
Dragging clutch, clutch is oil soaked, hydraulic release system is faulty.
What do you do when clutch won't engage?
So to me, " wont engage" means that you release the clutch and the car doesnt move. The clutch " wont disengage" Means that you step on the clutch but you cant get it to go into gear because the clutch didnt work. So the first one, wont engage. The clutch is worn or the pressure plate is busted. You need to pull the transmission and get into it and replace what is bad. The second one. Could be the fluid level is low or has air in it. Try changing the fluid and bleeding the air out of it. When under the car check the metal rod that pushes on the clutch throw arm. It should be moving in and out. Occcasionally the seal breaks and fluid runs out. If not trouble shoot the issue until it does move in and out at least 25 to 30mm. If this is good and moving in and out OK then the throw out bearing, pressure plate or clutch inside the housing is bad. You gotta pull the transmission and look inside to fix it.
1987 Porsche 944 will engage into gear but when you release the clutch you hear a clunk and it wont go what's wrong with it?
The throwout bearing in your clutch is the likely culprit here. Your clutch may be shot in addition, but you are probably looking at a costly fix here.
What is wrong if you have a 1994 Probe that wont go into 2ND 4TH or Reverse pushing clutch all the way in but will go into 1ST 3RD and 5TH shifting hard recently?
Most likely, the clutch or the clutch pilot bearing is dragging. This is caused by clutch hydraulic leaks not letting the clutch fully disengage or the clutch pressure plate/disc/flywheel is warped. Crawl under the car, (engine off)have a friend push/release pedal, see if slave cylinder throw seems adequate and look for leaks. If throw is short, problem is in the clutch hydraulics; if throw is normal, problem is the clutch.
1993 Acura Integra has some sort of problem with the clutch or shifter the car wont go into any gear when started but while off you can put it into gear after doing that you start it and it will stall?
The clutch is master and or slave cylinder are bad
Why does your car jerk when you let go of the clutch?
cause when you let go of the clutch the wheels start turning. holding the clutch keeps it in neutral.
