0
For all you whippersnappers, the device of which our friend speaks was designed to keep people from driving without their seat belts on. You couldn't start the car without buckling up, and it was federal law to install it in 1974 cars. The schematic for wiring around it is in the Bentley manual.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you take the seat off kawasaki 636?
How to remove the front seat: Remove the rear seat first by inserting the ignition key on the side of the bike (refer to the manual if you can't find it), on the very front of the compartment where the rear-seat was you will see a screw holding a metal belt, unscrew it and then slide the belt sideways (usually to the right). The front seat should get released and you can remove it and gain access to the battery etc.
How do you remove a dodge Dakota 2007 seat belt reminder?
1. With all doors closed and the ignition switch in anyposition except On or Start, buckle the driver's seat belt.2. Turn the ignition switch to the ON position and waitfor the Seat Belt Warning Light to turn off.3. Within 60 seconds of turning the ignition switch to theON position, unbuckle and then re-buckle the driver'sseat belt at least three times within 10 seconds, endingwith the seat belt buckled.NOTE: Watch for the Seat Belt Warning Light to turn onwhile unbuckling and off while re-buckling the seat belt.It may be necessary to retract the seat belt.4. Turn the ignition switch to the LOCK position. Asingle chime will sound to signify that you have successfullycompleted the programming.1. With all doors closed and the ignition switch in anyposition except On or Start, buckle the driver's seat belt.2. Turn the ignition switch to the ON position and waitfor the Seat Belt Warning Light to turn off.3. Within 60 seconds of turning the ignition switch to theON position, unbuckle and then re-buckle the driver'sseat belt at least three times within 10 seconds, endingwith the seat belt buckled.NOTE: Watch for the Seat Belt Warning Light to turn onwhile unbuckling and off while re-buckling the seat belt.It may be necessary to retract the seat belt.4. Turn the ignition switch to the LOCK position. Asingle chime will sound to signify that you have successfullycompleted the programming.
How do you replace a rear seat belt?
remove the seat to access screws
How do you disarm the seat belt alarm in a 2008 dodge Dakota?
1. With all doors closed and the ignition switch in any position except On or Start, buckle the driver's seat belt. 2. Turn the ignition switch to the ON position and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver's seat belt at least three times within 10 seconds, ending with the seat belt buckled. NOTE: Watch for the Seat Belt Warning Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt. 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have successfully completed the programming.
Cavalier seat belt remove?
To switch out a seat belt usually the seat needs to be removed first. Then it is in most instances just a bolt to be removed.
How do you remove seat belt buckle in a Toyota corolla?
Remove lower seat cushion by popping the front of it upward from the 2 retaining clips, then sliding it forward. The seat belt buckle is bolted to the floor.
How do you take a driver seat out of an impala?
On newer models, you have to move the seat all the way forward, remove side trim cover, remove seat belt anchor bolt, remove seat rails retaining bolts, tilt seat upward, disconnect wires, remove seat...
How do you disable seat belt chime in a 2005 dodge magnum?
The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. DaimlerChrysler does not recommend deactivating the Enhanced Warning System (BeltAlert). 1. Turn the ignition switch to the LOCK position and buckle the driver's seat belt. 2. Turn the ignition switch to the ON position and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver's seat belt at least three times within 10 seconds, ending with the seat belt buckled. NOTE: Watch for the Seat BeltWarning Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt. 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have successfully completed the programming. The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure.
How do you disable the seat belt alarm for the 2008 mercury mariner?
You Can't. It is wired through the ignition system, Disable it car won't run. Safer to wear seatbelt. Wrong. All Ford products can have the Belt Minder disabled. Here is how you do it on the Mariner: Turn the ignition switch to on. Wait approximately 70 seconds for the seat belt light on the dash cluster to go out. For the seat belt you want to disable the minder on, insert and remove the belt approximately 10 times, you'll want to do it until you see the seat belt light turn on again. Then unbuckle the belt and the light will flash 4 times per second for a few seconds to confirm. This also works on F-150 pickups I know for sure, I just did it to confirm.
How do you turn off the seat belt bell for a 2004 jeep liberty?
The following steps must occur within first 60 seconds of ignition switch being turned to ON or START position. 1) Turn ignition switch to OFF position, and buckle the driver's seat belt. 2) Turn ignition key to theACCESSORY/RUN position, and wait for the Seat Belt Warning Light to turn off. 3) Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver's seat belt at least three times within 10 seconds, ending with the seat belt buckled. 4) Turn the ignition key to the OFF position. A single chime will sound to signify that you have successfully completed the programming. The seat belt light will remain lit when belt is not fastened, but chime will not go off. To reactivate chime, repeat procedure 1-4 above.
How do you remove the front seats in a 2007 impala I see bolts on the rear of the tracks but not on the front of them?
Move seat fully forward, remove side trim, remove seat belt retaining bolt, remove seat tracks rear bolts, flip seat upwards, disconnect wiring, remove seat.....
How do you replace the female part of seat belt drivers side 97 ford explorer?
How do I remove the female seat belt assembly on a 97 ford exploer?
