answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered 2014-06-13 22:29:11

You can replace the locking cylinder, on your 1994 Ford Thunderbird, by removing the inside door panel. The locking mechanism will be visible with the door panel removed.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still Have Questions?

Related Questions

How do you remove the ignition lock cylinder from a 1988 Ford Thunderbird?

There will be a pin on the front bottom of the cylinder housing. Turn the key to the on position then push the pin in and pull the cylinder out.


How do you remove the ignition lock cylinder from a 1994 Ford Thunderbird with out a key?

rip it out or call a locksmith it happened with my 94 tbird


How do you find replacement lock for drivers door on 1988 Ford Thunderbird 5.0?

try oriely auto parts they have really cool cylinder locks


How do you remove and replace an ignition lock cylinder on a 1994 Ford Bronco?

Begin by removing the retaining ring at the top of your 1994 Ford ignition lock cylinder. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the ignition lock cylinder. Reverse the process to install your new ignition lock cylinder.


What causes lock cylinder to stay in start position?

It is defective and needs replacing.


Ford expedition starts with out key?

Replace the lock cylinder


How do you remove the ignition lock cylinder on a 1997 astro van?

Remove the retaining ring, from the top of your 1997 Ford Astro ignition lock cylinder. Remove the wiring harness from the back of the ignition lock cylinder.


How do you remove ignition lock key without key?

Removing a ignition lock cylinder from a 2002 ford windstar with no key


Replacing the ignition lock cylinder on 2000 Cadillac Catera?

how do you get ignition switch out of steering column in 2000 catera?


Ignition lock cylinder removal on a 94 ford escort?

How to remove and replace ignition lock on 94 escort lx wagon1.9


Where can you get spare tire carrier Lock cylinder for a 2005 ford F-150?

Your nearest Ford dealer for about $99.00


How do you reset a alarm 1997 Ford Thunderbird?

on my 93 u press door unlock on remote or with door open use door lock switch to lock doors close the door


Can a 1996 Ford Taurus replacement ignition lock cylinder be fitted to the original key?

Yes it can


Why is ignition switch on 1991 ford explorer hard to turn with key?

Try lubricating it with some graphite powder and see if that helps. Spray it directly into the key opening. You may also have a key that is worn badly and needs replacing.Ignition lock cylinder hard to turnYour probably refering to the ignition lock cylinder. The ignition switch is behind your instrument panel. If your ignition lock is hard to turn try spraying some wd40 inside the lock. If this does not work have ignition lock replaced it is worn.


How do you remove and replace an ignition lock cylinder on a 96 ford ranger?

after you take the plastic cover from around the steering colum, under the lock cylinder there should be a small access hole. you'll need a long thin tool to push up in there. on the cylinder lock itself there is a little pin that needs to be pushed in so the cylinder can be pulled out.


How do you change the ignition lock cylinder in a 1998 ford explorer with no keys?

I'm wondering if a locksmith is capable of getting your ignition lock cylinder to rotate to the on/run position so the ignition lock cylinder release can be depressed to remove it ? I'm also wonderering what they would charge for that service, because I was charged $30.00 and taxes to open my door lock on my house.


Where is the switch interruptor commutateur for a ford wind star 96?

I just installed an ignition cylinder (key lock) on a 1996 contour. On the box of the new ingnition lock cylinder it reads switch commutateur interruptor.


How do you remove the ignition lock on a 1995 Ford Thunderbird?

Remove the plastic cover under the steering column and the plastic steering column cover ( screws under column ) put the key in and turn to the run position, don't start on the bottom of the lock cylinder you will see a hole about the size of a paper clip you can use a paper clip insert into the hole and the cylinder will come out by pulling on it Then just reverse the procedure to put the new one in


Who invented the cylinder lock?

I think that Linus Yale Jr. was a lock manufacturer and patented the cylinder lock in 1861.


How do you remove the ignition cylinder in 2001 Ford Taurus?

Disconnect battery and leave disconnected for 10 minutes to power down airbag system. Turn lock cylinder to the RUN position. Locate a small hole directly under the lock cylinder in the plastic shroud. Insert a 1/8" drill bit into the hole and push up while pulling the lock cylinder out.


After replacing the ignition lock cylinder on a 1989 Ford Bronco how do you fix an automatic transmission that will not shift?

You replaced the ignition lock, and it will not shift out of park? If that is the situation, it sounds like the column is out of sync. More details are required to give a solid answer. A more common issue with these is the actuator rod in the column breaks. If you replaced the lock because it was turning hard and wasnt always cranking when turned, this may be your problem instead of the lock.


How do you replace lock cylinder mustang?

If you are talking about the ignition lock cylinder, turn the key to the accessory position, insert a paper clip into the little hole on the face of the lock cylinder to release the lock pin, turn the key a little further in a counter clock-wise direction and the lock cylinder will pull out. If you are talking about a door lock cylinder, remove the door panel, roll the window all the way up, pop the little clip loose on the lock rod that is hooked to the back of the cylinder and remove the rod from the lock arm, then pull the 'C' clip out that is holding the lock cylinder in place and push the lock cylinder out.


How do you replace an ignition lock cylinder on a Chevy S-10?

Remove the retaining ring at the top of your Chevy S 10 ignition lock cylinder. Slide the ignition lock cylinder out. Remove the wiring harness from the back of the ignition lock cylinder. Reverse the process to install the new ignition lock cylinder.


Where is the keypad code for a 1994 Ford Thunderbird?

look in the trunk behind the left side carpet there should be a bracket holding the lock control module this will have a sticker with the code on it.


How do you change door lock tumbler?

To change a door lock tumbler, remove the deadbolt and extract the lock cylinder. Turn the lock cylinder over and remove the plug from the cylinder. Replace with new tumbler.