0
Should the air induction blower continue to run after furnace blower motor starts?
Wiki User
∙ 14y ago
If you are refering to the inducer motor( the one with the little wheel that you see when you take your units doors off) Yes it should keep running when your blower motor is running and before ignition to create your draft and during to rid the gases out your flue Hope I kept it simple
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Which central heating system involves a furnace and a blower?
Forced air heating
Why nothing comes out of home vents when air is turned on?
IF BLOWER MOTER IS RUNNING CHECK FOR PLUGGED: FILTER BLOWER WHEEL OR MOST LIKELY (IF A 90+ FURNACE) THE SECONDARY HEAT EXCHANGER lc
What should the amp reading be Amp on 11kw motor - no load?
hi.. this is pankaj working as power engineer. we have a 11 kw induction motor which is used in fluidising blower. its no load current i sarround 9.5 to 10.6 amp. and under load its ampere does nt exceed 15 amp. its winding resistance is 1.4 ohm.
Will the gas go on and off until it reaches the correct heat in a gas furnace?
Yes, the thermostat in your home causes the gas valve to come on inside the furnace, although in some of the newer, high efficiency furnaces the process is a little more complicated. Furnaces usually detect the temprature inside the plenum and turn on the blower to move warm air into the home. Once the home is up to temperature, the gas is shut off and the blower will run until the plenum is cooled. The gas should not go off and on until it reaches the desired temperature. The gas should come on and the burners should stay lit until the desired temperature is reached. If this is not the case and the burners come on and off, you have a problem. If the burners come on and stay on until the temp set on your thermostat is reached then all is well. If you notice your burners are not lit and the temp is not reached and the blower is on, then you have a problem that needs a service tech. Your filter could be clogged or your flue pipe could be blocked or there may be a problem with your high limit.
How do you detect a crack heat exchanger in a furnace?
The most comon way to detect a crack in a heat exchanger is with a visual inspection, removal of the burner assembly and the use of a mirror and flash light. Or a smoke bomb test. A special little smoke bomb is placed in the burner area with the burners OFF. The blower is runnig and you light the smoke bomb, the smoke will draft up the flue vent or if a crack or rust hole is present then the smoke will get sucked into the air stream and come out of the duct work. Other than that using a carbon monoxide detector to see what the CO levels of the furnace are and comparing them to the supply air of the furnace to verify that there is no CO present in the air stream. The best and most accurate way is to contact a local Heating and Air Conditioning specialist or your local gas company should come out and perform a CO test on the furnace. Good Luck and God BLess
When furnace turns off blower will continue to run?
no
Where can one find a furnace blower motor?
Furnace blower motors are easily found at HVAC installers and repair centers. However, without proper knowledge, a customer should not try to fix this, it can be dangerous.
We have central heat and air. Does the furnace blower unit power on for the AC system too or is there a separate blower?
There should be only one blower to move the air. The unit will have a coil for cooling and a heat exchanger.
What size breaker do you use for a furnace?
It depends on the rating of the furnace. There should be a plate or sticker somewhere on the furnace that shows the rating. If you are just powering a blower motor the rating will be lower than if you have an electric heating element.
What are the features of a Clayton Wood Furnace?
Clayton Wood offers a lot of features on their Furnaces. To name some: Automatic draft induction blower included, Securdary Heat Exchanger and Twin 800 CFM blowers.
What is the power consumption of a gas furnace blower?
Watts
Is the air handler the furnace?
Yes it is. It contains the blower.
How do you change the filter in a Rudd Sihlouette II gas furnace?
turn off power to furnace and remove the bottom door to the blower compartment,the filter should be on the right side of the blower housing or it may be directly below the blower housing on the bottom of the furnace depending on how your return duct is run. hope this helps,FYI filters s/b replaced or cleaned every 30 days.
Where do i add sae 10 non detergent oil to my furnace blower motor?
To add the sae 10 non detergent oil to your furnace blower motor you will have to open the motor section.
Is there a diagram for adjusting blower speed on a ruud furnace?
Yes, It`s on the inside of the blower compartment cover panel.
A 3ton air conditioner has what size gas heater?
It could have any size heating furnace, the two are unrelated except for the size blower used in the furnace to support the 3 ton cooling system. But the fact remains you can get a 3 ton blower in 50,000 btu furnace, a 100,00 btu furnace and anything in between.
A fan or cooler relay is used in electric furnace to change the blower speed to the speed for cooling?
A fan or cooler relay is used in electrical furnace to change the blower speed to the blank speed for cooling
