answersLogoWhite

0


Best Answer

The problem is caused by the headlight switch in the turn signal lever. The headlight switch loosens over time and causes electrical shorts which make the headlight go out when the switch is jiggled. This happens most commonly when indicating in either direction.

The fix is to replace the turn signal lever. The lever is approximately $100 and can be easily replaced at home.

Unscrew 3 screws on the bottom of the steering wheel column cover. Push the steering wheel height adjustment lever all the way down to remove the cover.

The turn signal lever can then be removed by removing the electrical harness and unscrewing the two screws that secure it to the steering column.

Reverse the process to put in the new turn signal lever.

User Avatar

Wiki User

15y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: The front headlights on your 1999 Subaru Forester goes off sometimes when you use the turn signal?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do adjust my dash board light in your Subaru forester?

On my Subaru Forester the instrument panel lamps are dimmed by turning a ring on the turn signal stalk.


Where is the Subaru Forester dashboard light dimmer?

On my 2000 Forester, the dashboard illumination dimmer control is on the turn signal stalk. --Ken


How do you replace front turn signal assembly in a 2001 Subaru forester?

Turn signal lever assembly can be replaced without removing the steering wheel. See instructions at the attached link question about replacing the headlight switch on a 1999 Subaru Forester.


Where is the turn signal flasher unit on a Subaru Forester?

Look at the related link on why turn signals are not working for where the flasher unit is located.


Where is the turn signal and emergency flasher relay located on a 1998 Subaru Forester?

behind the fuse box underneath the drivers side dash


How you change 2007 Subaru Forester front signal bulbs?

2007 Subaru Forester turn signal light bulb replacement: Purchase the correct replacement turn signal light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the turn signal light bulb replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).


How you change 2007 Subaru forester front turn signal bulbs?

2007 Subaru Forester turn signal light bulb replacement: Purchase the correct replacement turn signal light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the turn signal light bulb replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).


What is the Hold signal on a console for in a 1998 Subaru Forester?

This is a Frost or Freeze Warning Indicatorsymbol. The snowflake symbol will come on in amber when the outside temperature drops to within a few degrees of freezing. At freezing or below, the symbol will be red.


Why does the turn signal blink when the headlights are out but not when the headlights are on?

That can happen when there is a bad ground to one of the lights.


Where Subaru Turn signal flasher?

In Subaru Car. Make clicking noises when work.


2002 Subaru Forester right turn signal light bulb divers side replace?

check the maintenance manual but all you need to do is unhook the power going to the light then take out the rubber linning and unscrew the retaining ring then replace lightbulb


How do you change turn signal light in 2003 subaru baja?

To change the turn signal light in the 2003 Subaru Baja you need to have a tool box with the necessary tools. Open the screws to access the turn signal light and replace it.