0
To remove engine from an '84 Vanagon do you need to remove tranny also?
Wiki User
∙ 14y ago
No. Not at all. Leave the transmission bolted up front, only undo the motor mount at the bell housing. When you undo the bolts at the bell housing, you can separate the motor from the transmission and roll it out from the back.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Why low rpm is required to carry heavy load in engine?
it puts less strain on the engine also better for the gears in the tranny
Where is the location on an 05 Harley sporster 883 can you refill gear oil for the transmission?
sporsters are all the same. they are what is called a unit case. this means engine and tranny are in the same case. unlike other hogs which have two cases,one for engine and one for tranny. so you dont check oil in sporster tranny because same oil for engine is tranny oil also. hope this helps yall.
What would cause a vibration in the engine when accelerating in a 1997 saburban?
are u sure its from the engine and not the tranny or front end? if from engine a motor mount or a bearing rubbing tranny may be slipping and catching or the torque converter, also front end may be worn if 4wd such as driveshafts and stuff or alignment
Can swap a 99 Camaro V6 Engine for an LS1 or LS3 engine?
Only if you also swap out the transmission because of the gear ratio in a v6 tranny is lower causing your engine to rev high
Can you convert the engine on the 280zx Non turbo to a Skyline GT R Twin turbo engine?
convert no!!! swap yes!!! You can use the rb26dett (thats the only twin turbo the skyline has) You can not use the tranny from the rb26dett(GTR)because it is AWD the rb25det can also be used(not a twin turbo) You would have to use the sr20det tranny or the tranny from a GTS also a skyline and some different motor mounts and a drive shaft but yes it can be done.
Can you put a 302 Ford engine in a 88 Pathfinder I know its possible but how do you get all your dash and gadets to work?
extended questionI'm also going to put the tranny and transfer case in it also so its not only the engine being replaced>
How can you drain all the transmission fluid from transmission?
Find the drain plug on the tranny oil pan. Loosen it and the fluid should start to drain - remove the plug all the way and let the contents go into a pan. When doing this, one also needs to change the tranny oil filter - this is accomplished by removing the tranny oil pan and changing it.
Will a Hyundai Tiburon engine bolt into a Hyundai Accent?
It is possible, some minor tweaking is necessary to make the engine mounts fit and also the drive axles but it is a fairly simple swap, you can even use the accent's tranny with the tib's engine. Also you will need to use the ECU that comes with the tiburon engine since the accent's ECU will not work with the 2.0 litre engine.
Can you replace Crankshaft on a Chevy cavalier 2.4l without removing engine?
No...The problem comes in with the bolts that hold the flywheel onto the crankshaft. You just cant get to them with the tranny still mounted. And then at the other end,you have the timing chain. And in the middle (inside the oil pan you have the chain that drives the oil pump. Also...cleanliness is a big factor....pulling the engine and tranny as a unit out the top is not that difficult, but it is designed to come out the bottom. All the plugins are different..remove the crank pully, the intake manifold(so to give more clearance for the exhaust pipe to clear the "arm" part of the tranny in the back part of the engine), the tranny mount from the car(driver side) and bend the corner of the battery tray alittle. Then peel back the brake master cylinder without removing any brake lines... It comes out without any problems.
How do you remove a Honda CB 750 engine?
This engine weighs 212 pounds. First, remove both wheels, the front forks and the swing arm. Remove all wiring and cables from the engine. Remove the carburetors. Then, remove engine mounting bolts except those at the bottom front and rear. Also remove the foot pegs. Next, remove top breather cover from engine. Remove oil filter and its housing. At this stage place the bike frame with the engine on its right side on some soft foam or blankets or such. Now you can remove the two remaining engine mounting bolts. The bike frame can be lifted off the engine at this point. Be careful with the engine mount tabs not to damage them.
What does a crankcase breather do?
The PCV or positive crankcase ventlation valve does as it is named. It will remove harmful gases from the engine. Also, you can find breather caps on the valve covers, this also helps to remove and fumes from the crankcase or engine base.
Are the 98 model cavaliers also equipped with a sealed tranny?
I have a 98 cavalier and its tranny is sealed....so yes.
