0
***CAUTION***The halogen bulb contains gas under pressure. The bulb may shatter if the gas envelope is scratched or if the bulb is dropped. Handle the bulb carefully. Grasp the bulb only by its base. Avoid touching the glass envelope. è The headlamp bulb should not be removed from the headlamp until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp. Headlights Removal & Installation 1. Raise and support the hood. 2. Raise the headlamp retainers by pushing rearward and pulling up. 3. If equipped, rotate the headlamp bulb protective counterclockwise and remove. 4. Disconnect the headlamp bulb electrical connector. 5. Remove the headlamp assembly. 6. Rotate headlamp bulb retainer counterclockwise and remove. 7. Remove the headlamp bulb by pulling it straight out with a gentle up-and-down rocking motion. ***WARNING*** Do not touch the glass bulb with your fingers. Oil from your fingers can severely shorten the life of the bulb. If necessary, wipe off any dirt or oil from the bulb with rubbing alcohol before completing installation. To Install; 8. Install a new bulb into the headlamp assembly. 9. Install the headlamp bulb retainer and turn it clockwise to engage the retaining tabs. 10. Attach the bulb electrical connector. 11. If equipped, install the headlamp bulb protective cover. 12. Install the headlamp assembly. è Be sure the headlamp assembly is positioned correctly with the alignment pins inserted into the proper holes and onto the ribs of the reinforcement. 13. Engage the retainers by gently pushing down. 14. Turn the lights on and check the bulb operation.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you replace the headlight bulb located on a 2004 Pontiac Grand Am?
1. Open the hood. 2. Remove the front air deflector. 3. Apply light pressure to the headlamp lens to hold the headlamp assembly in place while disconnecting the retainers. 4. Lift up the headlamp assembly retainers to release. Important: Note the location and position of the headlamp adjuster retainers and the locator tab. 5. Remove the headlamp assembly, pulling straight forward from the headlamp mounting panel. 6. Disconnect the wiring harness from the headlamp assembly. 7. Rotate the headlamp bulb/socket counterclockwise to release. 8. Remove the headlamp bulb/socket from the headlamp assembly, if required. There are (2) pull up clip retainers that hold the headlamp assembly in place...Both of these must be removed for the headlamp assembly to be pulled forward...:)
How do you replace the headlights on a 2002 Oldsmobile Bravada?
Each of the headlight assemblies are braced through the radiator support with a pair of retainers. The retainers for the right headlight assembly are in front of the battery. The retainers for the left assembly are in front of the washer fluid reservoir. Remove the retainers by pulling up on the retainer. With the retainers removed, the headlamp assembly falls forward. Reinstall the retainers to the square tabs on the headlamp assembly and the rivet on the radiator support
How do you replace the headlight assembly located on a 2001 Lincoln Continental?
for the removal, pull of the upper radiator sight shield, make sure that the headlamp switch and the ignition switch are turned off, raise the headlamp assembly retainers by pushing rearward and then pulling up to save time. disconnect the headlamp assembly wiring harness and remove the headlamp assembly, install just do the reverse.
How do you adjust the headlight on a Buick Century?
You will need to get the bulb, open the hood, locate the headlamp retainers, detach the power, take out the old bulb and then replace the bulb. For more instructions you can look at the owners manual.
How do you change the headlights in a 2003 Chevy Trailblazer?
I have a 2002 Trailblazer it took me forever to figure this out. To remove the headlamp assembly on a Trailblazer, remove the plastic panel that covers the hood latch assembly, remove the grill then release the retainers for the headlamp assemly. The bottom retainers for the grill are tricky and difficult to release. you can break the grill if done incorrectly. I'm told there is a way to change the bulbs without removing the grill but it seems to involve bending the grill in half and some severely scraped knuckles.
How do you replace the headlamp on a 2000 ford f150?
***CAUTION***The halogen bulb contains gas under pressure. The bulb may shatter if the gas envelope is scratched or if the bulb is dropped. Handle the bulb carefully. Grasp the bulb only by its base. Avoid touching the glass envelope. è The headlamp bulb should not be removed from the headlamp until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp. Headlights Removal & Installation 1. Raise and support the hood. 2. Raise the headlamp retainers by pushing rearward and pulling up. 3. If equipped, rotate the headlamp bulb protective counterclockwise and remove. 4. Disconnect the headlamp bulb electrical connector. 5. Remove the headlamp assembly. 6. Rotate headlamp bulb retainer counterclockwise and remove. 7. Remove the headlamp bulb by pulling it straight out with a gentle up-and-down rocking motion. ***WARNING*** Do not touch the glass bulb with your fingers. Oil from your fingers can severely shorten the life of the bulb. If necessary, wipe off any dirt or oil from the bulb with rubbing alcohol before completing installation. To Install; 8. Install a new bulb into the headlamp assembly. 9. Install the headlamp bulb retainer and turn it clockwise to engage the retaining tabs. 10. Attach the bulb electrical connector. 11. If equipped, install the headlamp bulb protective cover. 12. Install the headlamp assembly. è Be sure the headlamp assembly is positioned correctly with the alignment pins inserted into the proper holes and onto the ribs of the reinforcement. 13. Engage the retainers by gently pushing down. 14. Turn the lights on and check the bulb operation.
How do you change a headlamp on 2003 expedition?
***CAUTION***The halogen bulb contains gas under pressure. The bulb may shatter if the gas envelope is scratched or if the bulb is dropped. Handle the bulb carefully. Grasp the bulb only by its base. Avoid touching the glass envelope. è The headlamp bulb should not be removed from the headlamp until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp. Headlights Removal & Installation 1. Raise and support the hood. 2. Raise the headlamp retainers by pushing rearward and pulling up. 3. If equipped, rotate the headlamp bulb protective counterclockwise and remove. 4. Disconnect the headlamp bulb electrical connector. 5. Remove the headlamp assembly. 6. Rotate headlamp bulb retainer counterclockwise and remove. 7. Remove the headlamp bulb by pulling it straight out with a gentle up-and-down rocking motion. ***WARNING*** Do not touch the glass bulb with your fingers. Oil from your fingers can severely shorten the life of the bulb. If necessary, wipe off any dirt or oil from the bulb with rubbing alcohol before completing installation. To Install; 8. Install a new bulb into the headlamp assembly. 9. Install the headlamp bulb retainer and turn it clockwise to engage the retaining tabs. 10. Attach the bulb electrical connector. 11. If equipped, install the headlamp bulb protective cover. 12. Install the headlamp assembly. è Be sure the headlamp assembly is positioned correctly with the alignment pins inserted into the proper holes and onto the ribs of the reinforcement. 13. Engage the retainers by gently pushing down. 14. Turn the lights on and check the bulb operation.
How do you change a head lamp on a 2004 Buick rainier?
To change a head lamp on a 2004 Buick Rainer, first you will need to remove the headlamp retainers. This can be done by using and upward motion. Once this is done, dislodge the connector from the old bulb. The new bulb can now easily be connected, and the headlamp retainer placed back under the hood.
How do you get to the head lamp on an 03 expedition?
***CAUTION***The halogen bulb contains gas under pressure. The bulb may shatter if the gas envelope is scratched or if the bulb is dropped. Handle the bulb carefully. Grasp the bulb only by its base. Avoid touching the glass envelope. è The headlamp bulb should not be removed from the headlamp until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp. Headlights Removal & Installation 1. Raise and support the hood. 2. Raise the headlamp retainers by pushing rearward and pulling up. 3. If equipped, rotate the headlamp bulb protective counterclockwise and remove. 4. Disconnect the headlamp bulb electrical connector. 5. Remove the headlamp assembly. 6. Rotate headlamp bulb retainer counterclockwise and remove. 7. Remove the headlamp bulb by pulling it straight out with a gentle up-and-down rocking motion. ***WARNING*** Do not touch the glass bulb with your fingers. Oil from your fingers can severely shorten the life of the bulb. If necessary, wipe off any dirt or oil from the bulb with rubbing alcohol before completing installation. To Install; 8. Install a new bulb into the headlamp assembly. 9. Install the headlamp bulb retainer and turn it clockwise to engage the retaining tabs. 10. Attach the bulb electrical connector. 11. If equipped, install the headlamp bulb protective cover. 12. Install the headlamp assembly. è Be sure the headlamp assembly is positioned correctly with the alignment pins inserted into the proper holes and onto the ribs of the reinforcement. 13. Engage the retainers by gently pushing down. 14. Turn the lights on and check the bulb operation.
How can you change the headlights on expedition 1999?
***CAUTION***The halogen bulb contains gas under pressure. The bulb may shatter if the gas envelope is scratched or if the bulb is dropped. Handle the bulb carefully. Grasp the bulb only by its base. Avoid touching the glass envelope. è The headlamp bulb should not be removed from the headlamp until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp. Headlights Removal & Installation 1. Raise and support the hood. 2. Raise the headlamp retainers by pushing rearward and pulling up. 3. If equipped, rotate the headlamp bulb protective counterclockwise and remove. 4. Disconnect the headlamp bulb electrical connector. 5. Remove the headlamp assembly. 6. Rotate headlamp bulb retainer counterclockwise and remove. 7. Remove the headlamp bulb by pulling it straight out with a gentle up-and-down rocking motion. ***WARNING*** Do not touch the glass bulb with your fingers. Oil from your fingers can severely shorten the life of the bulb. If necessary, wipe off any dirt or oil from the bulb with rubbing alcohol before completing installation. To Install; 8. Install a new bulb into the headlamp assembly. 9. Install the headlamp bulb retainer and turn it clockwise to engage the retaining tabs. 10. Attach the bulb electrical connector. 11. If equipped, install the headlamp bulb protective cover. 12. Install the headlamp assembly. è Be sure the headlamp assembly is positioned correctly with the alignment pins inserted into the proper holes and onto the ribs of the reinforcement. 13. Engage the retainers by gently pushing down. 14. Turn the lights on and check the bulb operation.
How do you get to the bulb on an 2003 expedition?
***CAUTION***The halogen bulb contains gas under pressure. The bulb may shatter if the gas envelope is scratched or if the bulb is dropped. Handle the bulb carefully. Grasp the bulb only by its base. Avoid touching the glass envelope. è The headlamp bulb should not be removed from the headlamp until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp. Headlights Removal & Installation 1. Raise and support the hood. 2. Raise the headlamp retainers by pushing rearward and pulling up. 3. If equipped, rotate the headlamp bulb protective counterclockwise and remove. 4. Disconnect the headlamp bulb electrical connector. 5. Remove the headlamp assembly. 6. Rotate headlamp bulb retainer counterclockwise and remove. 7. Remove the headlamp bulb by pulling it straight out with a gentle up-and-down rocking motion. ***WARNING*** Do not touch the glass bulb with your fingers. Oil from your fingers can severely shorten the life of the bulb. If necessary, wipe off any dirt or oil from the bulb with rubbing alcohol before completing installation. To Install; 8. Install a new bulb into the headlamp assembly. 9. Install the headlamp bulb retainer and turn it clockwise to engage the retaining tabs. 10. Attach the bulb electrical connector. 11. If equipped, install the headlamp bulb protective cover. 12. Install the headlamp assembly. è Be sure the headlamp assembly is positioned correctly with the alignment pins inserted into the proper holes and onto the ribs of the reinforcement. 13. Engage the retainers by gently pushing down. 14. Turn the lights on and check the bulb operation.
How do you get to the head lamp on a 2003 expedition?
***CAUTION***The halogen bulb contains gas under pressure. The bulb may shatter if the gas envelope is scratched or if the bulb is dropped. Handle the bulb carefully. Grasp the bulb only by its base. Avoid touching the glass envelope. è The headlamp bulb should not be removed from the headlamp until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp. Headlights Removal & Installation 1. Raise and support the hood. 2. Raise the headlamp retainers by pushing rearward and pulling up. 3. If equipped, rotate the headlamp bulb protective counterclockwise and remove. 4. Disconnect the headlamp bulb electrical connector. 5. Remove the headlamp assembly. 6. Rotate headlamp bulb retainer counterclockwise and remove. 7. Remove the headlamp bulb by pulling it straight out with a gentle up-and-down rocking motion. ***WARNING*** Do not touch the glass bulb with your fingers. Oil from your fingers can severely shorten the life of the bulb. If necessary, wipe off any dirt or oil from the bulb with rubbing alcohol before completing installation. To Install; 8. Install a new bulb into the headlamp assembly. 9. Install the headlamp bulb retainer and turn it clockwise to engage the retaining tabs. 10. Attach the bulb electrical connector. 11. If equipped, install the headlamp bulb protective cover. 12. Install the headlamp assembly. è Be sure the headlamp assembly is positioned correctly with the alignment pins inserted into the proper holes and onto the ribs of the reinforcement. 13. Engage the retainers by gently pushing down. 14. Turn the lights on and check the bulb operation.
