answersLogoWhite
Car Stereos and Speakers
Chevy Blazer
GMC Sonoma
Chevy Blazer S-10

What are the speaker sizes for a 91 S10 blazer?


Top Answer
User Avatar
Wiki User
Answered 2009-05-17 18:22:06

4x6 in the front (dash mount)

6x9 in the rear kick panels (2 door ONLY) 6 1/2" round in the rear doors (4 door ONLY)

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Still Have Questions?

Related Questions

What is the timing degrees for a 91 s10 blazer 4.3 2wd?

on a 91 blazer s10 4wd


91 s10 what years interchange grille?

any first gen s10 0r blazer or bervada grills will fit


Where is the throtle position sensor on a 91 Chevy s10 blazer?

On the drivers side of the throttle body.


91 grill in a 87 s10 blazer?

This can be done, though some modifications may be needed. If you need to replace your core support (rad support) as well, order a core support for a 91 S10 blazer. This will help do away with the mounting issues. I did this to a 1985 S10 blazer and the grill fit fine with the factory core support, but not all of the mounting locations matched.


What are the speaker sizes in my 91 explorer Eddie Bauer edition?

6x8.


Where is the egr valve on a 91 s10 blazer 4.3 v6?

It is behind the throttle body, on the intake manifold.


How to Drain oil on 91 S10 Blazer?

To drain the oil on a 1991 Chevy S10 Blazer, located the oil pan drain plug. Use a wrench to remove the plug and the oil will flow into the receptacle you have provided.


Is a 91 Chevy S10 blazer temp control vacuum or cable operated?

Neither, I believe it's electric.


What kind of oil does a 91 Chevy s10 blazer use?

I have always used 10w30. never had any problems.


Where is the rear window defogger relay on a 91 Chevy S10 Blazer?

It is located under the AC and Heat instrument panel


What is the proper tire pressure for a 1991 Chevy S10 blazer?

your question should be , whats the proper pressure for the tiers on my 91 s-10 blazer this information is embossed on your tiers


How much horsepower does a 91 s10 blazer 2WD 4.3L have?

160-165 horsepower. 230-235 foot pounds of torque.


Where is the fuelpump located on a 91 s10 blazer?

Inside the fuel tank. The fuel tank must be removed to gain access to the pump.


What are the engine specs of a 91 Chevy s10 blazer?

4.3 L V6 160-165 H.P. 230-235 Lb/Ft Torque


How do you install a fuel pump on a 91 s10 blazer?

drop the gas tank then spin the lock ring off, take out and put new one in.


How do you locate the starter on a 91 Chevy s10 blazer 4x4?

Follow the positive battery cable from the battery down, the other end will be attached to the starter.


Should there be power in both wires that go to the fuel pump on 91 s10 blazer?

No. Only one wire should have power, the other is the ground.Type your answer here...


What is the best way to repair body damage of a 91 Chevy blazer s10 two wheel drive?

The best way would be to replace the damaged panel.


Will a fuel pump from a 91 s10 fit a 97 s10?

No.


How hard is it to replace heater blower on 91 S10 Blazer?

its not vary hard its on the passanger side of the vehical under the hood atached to the fire wall with 4 screws


Where do you find the odometer cable and gear on a 1994 s10 blazer 4x4?

Most all GM vehicles switched to an electrical unit around '91. There won't be a cable.


Will a 1994 astro transmission fit a 1991 s10 blazer?

It'll fit, but it won't work. The 94 transmission is electronic, and interfaces with the ECM. It won't be compatible with the 91 in that regard.


Why would 4x4 on 91 s10 blazer stop working?

if the 4x4 isn't working then you need to check your transfer case. is it making any noises? or did it just stop working?


Will a 91 s10 blazer windshield fit an 85 s10 pick up?

Yes. The body style for the s10s from 1982 to 1993 are the exact same thing. Only cosmetic changes were ever made, such as a different grill was used in 91. The 82 - 93 year models share the same exterior parts, including the windshield.


How do I fix or replace the high-low beam switch in a '91 Chevy s10 Blazer?

u have to take the hole thing apart to get to a small screw to take the switch out


Still have questions?