answersLogoWhite

0


Best Answer

They are 43 Ft. lbs

User Avatar

Wiki User

โˆ™ 2006-04-08 23:54:29
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: What are the torque specs for the main bolts on the water pump of a 1993 Jeep Cherokee Sport 4.0 liter 6-cylinder?
Write your answer...
Submit
Related questions

What are the specs to torque head bolts on 1991 jeep Cherokee?

thank you


Jeep Cherokee torque specs front axel carrier bolts?

60ft/lbs


What are the torque specs for the flywheel bolts on a 1993 jeep grand Cherokee 4.0?

105 ft


What is the torque specs on trans pan bolts 99 grand Cherokee Laredo?

144 in-lbs


Trying to put a 2002 grand Cherokee motor in 2000 Cherokee sport and the motor mount bolts are different?

Not sure how to help, other than you will have to use bolts that fit.


Where is the transfer case on a 2000 jeep Cherokee sport?

It bolts to the back of the transmission.It bolts to the back of the transmission.


What is the torque specs for the brake caliper mounting bolts on a 99 Jeep Grand Cherokee?

77 foot pounds


How many bolts to take off starter on a 94 jeep Cherokee sport?

Either 2 or 3


Torque specs and sequence 1998 Jeep Cherokee?

The 1998 Jeep Cherokee head bolt torque specifications is 120 pounds. The head bolts should be tightened by starting at one and alternating to the other end, working towards the center.


What are the cylinder head torque specs and sequence on a Jeep Cherokee 4.0 engine?

The Jeep Cherokee 4.0 liter engine cylinder had torque specifications are 120 pounds per square inch. The cylinder head bolts should be torqued at 40 pound intervals.


What are the valve cover torque specs for a 2001 3.0 Mitsubishi Montero Sport?

The 2001 Mitsubishi Montero Sport 3.0 liter engine valve cover torque specification is 40 pounds. You do not want to over torque the valve cover bolts, as you may ruin the valve cover gasket.


What are the cylinder head bolt torque settings on a 2001 Jeep Cherokee 3.7L V6 engine?

The 2001 Jeep Cherokee 3.7 liter engine cylinder had bolt torque specification is 150 pounds. The cylinder head bolts should be torqued in 50 pound intervals.


What are the tie rod ends torque bolt settings on a 2000 Jeep Grand Cherokee Laredo FWD?

The tie rod torque bolt settings, on your 2000 Jeep grand Cherokee, is 70 pounds per square inch. The bolts should be torqued in 35 pound intervals.


What tool do you need to get the front caliper off a 1990 Cherokee sport?

a 12 mm socket 2 bolts on the back of the caliper


Where is the throttle position sensor on a 1999 Jeep Cherokee Sport?

It bolts to the side of the throttle body opposite of where the throttle cables attach.


What is the torque specifications for the water pump attaching bolts on a 2005 Jeep Grand Cherokee 5.7L HEMI?

18 ft lbs, 24 NM


What is the torque for an 1986 Dodge 318 rod bearing bolts?

the correct torque for these bolts is as follows: 96lbs


What is the torque specs for the brake caliper mounting bolts on a 1999 subaru legacy?

Front caliper mounting bracket bolts torque to 57ft-lbs Front caliper pin bolts torque to 27ft.lbs Rear Caliper mounting bracket bolts torque to 38ft-lbs Rear caliper pins torque to 15ft-lbs


What is the torquing specs for the bolts on a 1999 blazer 43 intake manifold The book gives 132 pounds but this seems too much?

I FOUND THIS AT WWW.AUTOZONE.COM, CLICK ON VEHICLE SPECS . For your 1999 CHEVROLET TRUCK BLAZER 2WD: INTAKE BOLT TORQUE FOOT POUNDS (FINAL TORQUE) TORQUE LOWER MANIFOLD BOLTS TO 27 IN/LBS TORQUE LOWER BOLTS TO 9 FT/LBS TORQUE LOWER BOLTS TO 11 FT/LBS TORQUE UPPER MANIFOLD BOLTS TO 44 IN/LBS TORQUE UPPER MANIFOLD BOLTS TO 7 FT/LBS (TO TORQUE BOLTS & NUTS, START IN CENTER USING CRISSCROSS PATTERN)


How much is the torque of 2c cylinder head bolts Toyota?

torque for 2c engine cylinder head bolts


What size socket is needed to remove the top two bolts in the bell housing on a 1996 jeep Cherokee sport?

E12 external torx


What size bolts go in Flywheel on a 1993 jeep Cherokee sport?

18 mm head by half inch long fine thread


What is the torque spec for the idler pulley on a 1995 Jeep Cherokee?

Haynes says that the pulley bracket to block bolts should be torqued to 14 ft/lbs.


Torque specifications bolts suzuki esteem?

torque specifications


What is the torque spec for front brake caliper bolts on a 2001 Toyota tacoma prerunner?

Brake caliper bolts torque is 90ft-lbs. Wheel Lug Nut torque is 83ft-lbs. Brake caliper bolts torque is 90ft-lbs. Wheel Lug Nut torque is 83ft-lbs.