0
What are the torques on 3800 series 2 lower and upper intake bolts?
Wiki User
∙ 9y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the torque specifications for the intake manifold on a 1997 Chevrolet vortec 350?
Install the lower intake manifold to the engine. Apply sealer, GM P/N 1052080 or equivalent, to the lower intake manifold bolts.Install the lower intake manifold bolts. Tighten the bolts in three steps:TightenTighten the bolts on the first sequence to 8 N·m (71 lb in).Tighten the bolts on the second sequence to 12 N·m (106 lb in).Tighten the bolts on the final sequence to 15 N·m (11 lb ft).I this is what you are looking for.GMmechanic@gmail.com
What are torque specs intake bolts on 3.4l 2002 Chevy impala?
lower intake is 132 lb's upper intake is 89 lb
What are the torque specs on intake manifold bolts and exhaust manifold bolts for a 97 Chevrolet Cavalier 2 2 liter engine?
24 ft lbs lower intake 115 inch lbs exhaust
How do you change the lower intake gasket on a 95 Olds Cutlass Supreme 3.4DOHC?
Remove the 1995 Oldsmobile Cutlass intake manifold retaining bolts. The manifold will come off. Remove the old gasket. Clean the surface. Put the new intake gasket and tighten the intake manifold retaining bolts.
Remove the power steering pump to remove the lower intake manifold bolts?
If you plan to remove the lower intake manifold, you probably have to remove pwr steering pump indeed. Otherwise it makes a difficult removal/installation.
What is the torque for the rocker arms on a 1998 Malibu And the torque on the intake bolts?
for the rocker arms bolts its-- 98 and later, step 1- 168 in-lbs. step 2-- rotate an additional 30-degrees. this is all for a 3.1 v6, the intake bolts are -- (lower) step 1, 62 in-lbs, step2, 115 in-lbs, intake manifold bolts/studs(upper)---18 ft-lbs,
Intake manifold torque spec on 1993 Nissan maxima?
# Upper intake manifold bolts 13 to 16 ft-lbs # Lower intake manifold bolts/nuts # Step One (ALL) 26 to 43 in-lbs # Step Two (BOLTS) 144 to 168 in-lbs # Step Three (NUTS) 17 to 30 ft-lbs
What are the torque specs for a 1993 Buick lesabre intake manifold?
You did not mention if it was the intake to the cylinder head bolts (1993 buick lesabre 96 in-lbs)..... or ..... the intake upper to lower bolts ( 1993 buick 132 in -lbs) but i hope you will know wich you are looking at since there is a large difference in torqe.
Torque specs on 2002 s-10 with 4.3 engine for the intake?
Tightening the bolts in the typical order from the middle out, the upper intake bolts torque in first pass at 44 in lbs, the second pass at 88 in lbs. The lower intake bolts start with 27 in lbsfor the first pass, 106 in lbs for the second pass and 133 in lbs for the last pass.
What is the torquing specs for the bolts on a 1999 blazer 43 intake manifold The book gives 132 pounds but this seems too much?
I FOUND THIS AT WWW.AUTOZONE.COM, CLICK ON VEHICLE SPECS . For your 1999 CHEVROLET TRUCK BLAZER 2WD: INTAKE BOLT TORQUE FOOT POUNDS (FINAL TORQUE) TORQUE LOWER MANIFOLD BOLTS TO 27 IN/LBS TORQUE LOWER BOLTS TO 9 FT/LBS TORQUE LOWER BOLTS TO 11 FT/LBS TORQUE UPPER MANIFOLD BOLTS TO 44 IN/LBS TORQUE UPPER MANIFOLD BOLTS TO 7 FT/LBS (TO TORQUE BOLTS & NUTS, START IN CENTER USING CRISSCROSS PATTERN)
How do you take off Intake manifold on a 1992 s10 blazer?
upper or lower? either way, remove all wiring, 8 10mm bolts that hold upper intake, both fuel lines in right rear(inlet, outlet) remove upper intake. 8 13mm bolts hold lower intake. dont need to remove lower intake if u r replacing injector assemble which is probably what u r doing as this is a very common problem with the vortex engine. be sure to replace as assembly and not just regulator if the vehicle has 100k plus
Will a 1999 Malibu upper intake fit a 2000 Malibu?
The '99 has more bolts. If you have the lower intake also, you can swap the whole thing. The upper alone wont fit. Intake issues are very common for these cars.
