Firearms
HDTV
Honda Civic LX
VW Cabrio

What does the lever on top of the receiver on a Universal m1 carbine do?

424344

Top Answer
User Avatar
Wiki User
2005-10-02 18:08:56
2005-10-02 18:08:56

dWhen you draw back the bolt and push forward on the lever, it holds the bolt open.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

When the receiver is locked closed, remove the forearm using the lever on the bottom of the wood. Next keep a firm grip on barrel and receiver, break the gun open by the lever on the top of the tang. When broke open the barrels will lift off and separate from the receiver and stock.

User Avatar

Not sure which spring you mean, or what you mean by "case"? If you mean the receiver, then you might be referring to the cartridge cutoff spring, or the lever spring? The lever spring is held by a screw just in front of the lever pivot screw, and keeps pressure on the lever, so it wont droop. The cartridge cutoff spring installs in the top of the receiver, with a screw through the top that holds it just behind the chamber. These are my best guesses, since i don't have good info.

User Avatar

It depends on the model. The numbers are always on the receiver, never the barrel. Pumps and autos are on the bottom of the receiver, forward of the carrier. Over/Under serial numbers are under the action release lever on top of the tang. Move the lever to open and you will see the serial number.

User Avatar

It depends on a lot of factors. Is the crest still on the top? Is it the long rifle or the carbine? Does the bolt lever stand out straight or is it curved down? Do the serial numbers all match? What is the overall condition? Regardless, the range is $125.00 to 450.00. It depends on a lot of factors. Is the crest still on the top? Is it the long rifle or the carbine? Does the bolt lever stand out straight or is it curved down? Do the serial numbers all match? What is the overall condition? Regardless, the range is $125.00 to 450.00.

User Avatar

Between August and November 1944.This block of serial numbers were assigned by the Federal goverment to Inland Division of General Motors.This should be marked on top of the rear of your receiver.

User Avatar

Johny lever because he owns hindustan lever

User Avatar

They are both because the staples are the wedges and the top arm of a stapler is the lever.

User Avatar

There are 2 grooves cut into the top of the receiver to except matching bases and rings to mount a scope on top of your .22 caliber rifle.

User Avatar

Padded Receiver gloves are padded on the top of the hand and fingers and regular receiver gloves are not padded. Both feature the same sticky grip.

User Avatar

the top is the giver while the bottom is the receiver

User Avatar

the one on the side holds the trigger group in the receiver . the one on top has to do with the scope mount wich is unique to these guns

User Avatar

Check under the top lever.

User Avatar

A stick on top a piece of cobblestone

User Avatar

toilet handle (lever), spray bottle top (lever) and sink top (wheele and axle).please subscibe and like if this helped! :)

User Avatar

The pile fell over, so now none are on top

User Avatar

it's a lever because there is a fruculm on the end effort and force im the middle and resistance at the top

User Avatar

In 2010, wide receiver Mike Wallace led the Steelers in receiving yards (1,257) and receptions (60).

User Avatar

Slide the Top Lever to the right to open the chamber. Turn the shotgun upside down. Look at the end of the barrel between the receiver and barrel. Get a flashlight and you'll see a series of numbers stamped in the bottom of the barrel.

User Avatar

the switch is in the lever pull backwards or push forward on lever once released

User Avatar

on top of the gearbox under the clutch lever

User Avatar

I had trouble too. If it's like mine, there is a black plastic key on the underside of the start lever box . You insert it in the slot on the top of the start lever box and then release the lever and pull it back to the handle. I hope this helps you. I had trouble too. If it's like mine, there is a black plastic key on the underside of the start lever box . You insert it in the slot on the top of the start lever box and then release the lever and pull it back to the handle. I hope this helps you.

User Avatar

There is a small lever by the door at the top of the back seat. Flip the lever and the seat should fold down.

User Avatar

go to the top of the crane and switch the lever.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.