0
What goes in the hole next to the distributor on a 283 engine block?
Wiki User
∙ 16y ago
Maybe the coil pack don't know what hole you are talking about
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How can you tell a Chevy 350 engine from a Pontiac 350 engine?
On a small block Chevy the distributor goes through a hole in the intake manifold. On a Pontiac the distributor goes behind the intake manifold.
How do you know the front and back on a 302 engine?
Look for the hole into which the distributor is to go, assuming that it is a bare block you're talking about: the distributor goes up front. jb
What is a Hole in engine block?
A hole in the engine block is God's way of telling you to get a different car. You get a hole in the engine block when a piece of your engine--normally a rod cap--comes off at full speed and goes through the side of the block. And there's no way to fix it.
Were is the oil pressure sending unit for a 67 283?
If the intake is on it, Look at the back of it where the distributor goes in it and just behind the intake were it seals against the back of the block you will see a small hole in the top side of the engine block. That is the oil pressure port.
What goes in distributor hole on 6.2?
The dristibutor
Does the spring end face the engine block or face the radiator on an 1996 Ford explorer thermostat installation?
The spring faces the engine block ( and the vent hole goes to the top )
What causes a hole in a engine block?
A hole in your block comes from massive mechanical failure. Mostly a broke rod or crank. If you have a hole in your block, you need a new motor.
What goes in the hole in the back of the head on the passenger side of the engine on a 79 305 v8?
If you mean the hole that is tapped 3/8-16, it is often used for a ground strap connecting from the block to the firewall.
What direction does the thermostat go in 93 ford explorer?
The spring goes towards the engine , and if the engine thermostat has a vent hole , the hole goes at the top
Where does the oil pressure gauge go on a small block Chevy 350?
There is a 1/8"npt port on the back rail of the block near the distributor hole.
What is the proper timing degree for a long block 4.0 1993 Jeep Wrangler?
2.5L and 4.0L ENGINE NOT ROTATED 1. Clean the mounting area of the cylinder block and install a new distributor mounting gasket. On some models there is a fork on the distributor housing. The slot in the fork aligns with the distributor hold-down bolt hole in the engine block. The distributor is correctly installed when the rotor is correctly positioned and the slot is aligned with the hold-down bolt hole. On these computer controlled distributors, initial ignition timing is not adjustable. 2. Align the rotor tip with the scribe mark on the distributor housing during removal, then turn the rotor approximately 1/8 turn counterclockwise past the scribe mark. 3. Slide the distributor shaft down into the engine. It may be necessary to move the rotor and shaft slightly to engage the distributor shaft with the oil pump slot. Align the scribe mark on the distributor housing with the mark on the cylinder block. Ensure that the distributor is fully seated against the cylinder block. It may be necessary to slightly rotate (bump) the engine while applying light downward force to fully engage the distributor shaft with the oil pump drive gear shaft. 4. Install the distributor shaft hold-down and bolt. Tighten the bolt to 17 ft. lbs. (23 Nm). 5. Install distributor cap and ignition wires. Insure that the wires are routed correctly before attempting to start engine. ENGINE ROTATED 1. Rotate the engine until the No.1 piston is at TDC compression. 2. Using a flat-bladed screwdriver, in the distributor hole, rotate the oil pump gear so that the slot in the oil pump shaft is in the correct position (see illustration). 3. With the distributor cap removed, install the distributor so that the rotor is positioned correctly (see illustration). Insure that the distributor is fully seated against the cylinder block. If not, remove the distributor and perform the entire procedure again. 4. Tighten the hold-down bolt. 5. Install distributor cap and ignition wires. Insure that the wires are routed correctly before attempting to start engine.
What is cylinder bore?
This is the diameter of the cylinder hole in the engine block for the pistons.
