320 grit
I would use a fine grit like 220 or so.
Initially, you can use as any grit you need to get the area straight, once it gets near that stage you need to step up in the grit to remove scratch marks. I would not prime any surface with greater sanding marks than were done with 220 grit. After priming I would block with 400 grit wet or dry
220 3m its a finer sand paper you can take the paint as low as you want with it it works great. You should always prime over a 220 grit scratch. It is the perfect size grit. If you are sanding primer so you can apply topcoat, finish with 400grit dry on a machine (DA) or 500 wet sand for a solid color enamel. Basecoat products, particularly metallics and pearls, need to be applied over a substrate that has been wet sanded with 600 grit.
400 grit sandpaper, before sanding melamine wash the surface with TSP soap and the rinse with water to remove any TSP residue
I have used 320 grit all-purpose sand paper. But if you find this isn't removing the brass, you can go to a 240 grit or so. Remember you are only scuffing the surface, it is just to remove the gloss so the primer has something to adhere to. I have used 320 grit all-purpose sand paper. But if you find this isn't removing the brass, you can go to a 240 grit or so. Remember you are only scuffing the surface, it is just to remove the gloss so the primer has something to adhere to.
Answer: I would start with a 400 grit sandpaper then a 1500 grit sandpaper then I would use a paste car wax to get a nice shine.
I would use a fine grit like 220 or so.
You would not use sandpaper. You would use a screen. The sanding screens usually come in an 80, 120, and 220 grit.
Grit refers to the fineness of the sandpaper. Depending on the application for which you wish to use the sandpaper, choose the correct grit size. Example, general finish for timber flooring or fine finish for coffee tables etc.
Initially, you can use as any grit you need to get the area straight, once it gets near that stage you need to step up in the grit to remove scratch marks. I would not prime any surface with greater sanding marks than were done with 220 grit. After priming I would block with 400 grit wet or dry
You can reduce the weight of a cricket bat by using sandpaper. You can use 100 or 80 grit sandpaper to sand the bat down.
After primer is applied, use 220-grit sandpaper for a smooth surface. Change sandpaper frequently, and wipe the primer down to remove dust. Vacuum the floor to remove the dust, and keep it from flying back up onto the primered surface.
To remove scratches u must use fine grit sand paper starting with 220 grit and progressing to super fine 600 grit sandpaper
You need a fine grit sandpaper to clean untreated softwood floor. Use the fine grit sandpaper to gently clean the wooden surface as the dust is wiped away. This procedure should be repeated until the stain is no more.
The higher the number code printed on the back of all sandpaper the finer the grit. With a little practice you can begin to understand what grit is appropriate for any given job. For instance, I refinish hardwood floors and it requires three courses of sanding. To help quickly remove an old finish from hardwood floors I start with a very course #20 sandpaper. It is so rough that it removes a large amount of material pretty quickly. Then, when I have sanded the floor down to bare wood I "step up" to 60 grit sandpaper. Once I've gone over the entire floor with the 60 grit I "step up" again to the finer 100 grit paper. When refinishing wood floors or furniture it is necessary to use several courses of sanding to help remove the deep scratches created by the rougher grits of sandpaper. I hope this helps. John
120 or 100 grit 80 if it is high
220 3m its a finer sand paper you can take the paint as low as you want with it it works great. You should always prime over a 220 grit scratch. It is the perfect size grit. If you are sanding primer so you can apply topcoat, finish with 400grit dry on a machine (DA) or 500 wet sand for a solid color enamel. Basecoat products, particularly metallics and pearls, need to be applied over a substrate that has been wet sanded with 600 grit.