Want this question answered?
The tables within Appendix 4; "Current-carrying capacity and voltage drop for cables and flexible cords." 4D1 to 4J4. For each type of cable, you will find (with a couple of exceptions) a Table A for current-carrying capacity values and following it, a Table B for voltage drop values.
The current capacity of a cable varies depending on the type of conductor material, and the type and rating of the insulation. An excellent table that shows the capacity of different types of cables can be found here: http://www.myelectrical.com/pages/cables/cableCurrents.aspx?id=061112125012. Also, the current capacity of a cable will be limited by the electrical code that one is using, this varies in each developed country. Most American companies use NEC (National Electric Code) as there source for electrical codes (the most recent version being NEC2008), and much of the rest of the world will use ICC EC (International Code Council Electric Code).
There's no such word as "'Ampacity". The current carrying capacity of 50mm cable is around 300A continuous or 365amps @ 60% duty cycle. It's generally used for engine starter circuits or high current welders.Answer'Ampacity' is a North American term for the 'current-carrying capacity' of a cable. It is not used in most other English-speaking countries.
Cables spaced apart on cable ladder, shaded from sun
The answer to the first part of your question is yes but the wire size has to be of a size specified in the electrical code for wires connected in parallel. As for the second part of the question the total current output is governed by the current draw of the load. It is the load current that governs the parallel wire size and the trip capacity of the breaker.
if you know the gauge of the wire you can learn its current carrying capacity
Finolex Cables was created in 1958.
It will just be the sum of the current-carrying capacity of each individual cable.
Transmission power cables are designed by current carrying capacity.
The tables within Appendix 4; "Current-carrying capacity and voltage drop for cables and flexible cords." 4D1 to 4J4. For each type of cable, you will find (with a couple of exceptions) a Table A for current-carrying capacity values and following it, a Table B for voltage drop values.
In European countries and elsewhere, the cross-sectional area of electric cables and busbars are expressed in square millimetres. The larger the cross-sectional area, the greater the current-carrying capacity.
Upto about 16 Amps, provided the cables aren't wrapped or bunched up somewhere hot.
It depends on some factors which are not mentioned in the question. The main difference between 100% copper wire and copper clad aluminum is that IF they are the same diameter, then the copper will carry and stand up to more electrical current than the aluminum. If the diameter of the aluminum cables have been upgraded in size, to match the current carrying capacity of the normal copper cables, then the only remaining difference is that copper withstands much more bending and coiling beforethe metal begins to "work harden," and some of the individual wire strands begin to break. In other words, the copper stands up to use better than aluminum. When buying booster cables, read the lables, and make sure that the maximum number of Amps, for which the aluminum cables are capable of carrying, is equal to or greater than the highest rated copper cables. Therefore, IF the copper clad aluminum cables are rated for the same current carrying capacity as copper cables, then there is NO difference in use between the two types.
Increases
For the common small cables used in domestic electricity the maximum current for a short time is 10 amps per mm2, reducing to 8 A/mm2 for loads that are on for 1½ hours per day, to 4 A/mm2 for loads that are on for 6 hours/day, and to 2 A/mm2 for continuous loads. Currents higher than the above will give excessive energy losses in heating the cables.
4amps can pass in 1sqmm of wire max it is universal. In the UK 1 sq. mm wire can take 10 amps max according to tables. Cables that become warm in use should be replaced by a thicker gauge.
The "current choking" means that the maximum capacity of a transformer is not being utilized. To prevent it from ever reaching its maximum capacity a lower value of over current protection or fuse is installed. The purpose is to use larger capacity transformer available but using smaller distribution and cables just sufficient for the application to lower the installation cost.